What to do if my BidetMate Toilets are not working (power button)?
First, check that the plug is securely attached. Inspect the circuit. If the power light isn't on, press the rotated switch for 3 seconds to turn it on. If the leakage protection plug light is off, unplug the unit, then plug it back in. Press the reset switch on the leakage protection plug. If it still fails, unplug the unit and contact a local distributor for repairs.
What to do if there is no water from the spout of my BidetMate BM-6000 Toilets?
If there's no water coming from the spout, first check if the water supply is cut off and wait for it to be restored. Then, ensure the angle valve is open. Also, inspect the water filter for blockages and clean or replace it if necessary. Finally, make sure the inlet pipe is straight and not flexed.
What to do if the intensity of cleaning is not strong enough on my BidetMate BM-6000?
If the cleaning intensity is too low, first check the water pressure setting and adjust it according to the instruction manual. Also, inspect the inlet filter for any blockages and clean the filter mesh or replace the water filter if needed.
Why is the dryer blowing cold air in my BidetMate BM-6000?
If the dryer is blowing cold air, first check if the dryer is switched off and regulate the temperature according to the instruction manual. If the issue persists, it is recommended to contact qualified maintenance personnel for repair.
What to do if the water temperature is not warm enough in my BidetMate BM-6000 Toilets?
If the water isn't warm enough, check if the water supply is set to a low level and adjust the water temperature according to the instruction manual.
What to do if the seat temperature is too low or not hot on my BidetMate BM-6000?
If the seat isn't warm enough, make sure the toilet seat temperature isn't set to the 'off' position. Adjust the temperature according to the instruction manual.
What to do if there is unusual water flow from the spout of my BidetMate BM-6000 Toilets?
If you notice unusual water flow from the spout, unplug the unit for one minute, then plug it back in.
What does it mean if the blue light of water temp is flickered on my BidetMate Toilets?
If the blue light for water temperature is flickering, it likely indicates a low battery. Replace it with a new one.
What to do if the cleanser is always leaking from my BidetMate BM-6000?
If the cleanser is constantly leaking, it suggests the solenoid valve may no longer be working. Contact qualified maintenance personnel for repair.
What to do if the cleaning function is not working normally on my BidetMate BM-6000?
If the cleaning function isn't working correctly, it might be due to a problem with the human induction system of the toilet seat. Contact qualified maintenance personnel for repair.
Essential safety guidelines for electrical product usage, especially with children.
Proper grounding procedures to prevent electric shock and ensure product safety.
Defines warning, attention symbols, and general safety precautions for user understanding.
Warnings regarding grounding, wet hands, fire hazards, and proper power socket usage.
Precautions against harsh cleaners, water immersion, and humid environments.
Guidelines for seat usage, battery handling, and avoiding direct heat/sunlight.
Verifies water pressure requirements and confirms product fit within the installation space.
Diagnoses and solutions for problems related to the power button and washing functions.
Troubleshooting steps for dryer, heated seat, remote control, and toilet unit malfunctions.
General| Brand | BidetMate |
|---|---|
| Model | BM-6000 |
| Material | Plastic |
| Water Heater Type | Tankless |
| Nozzle Type | Stainless Steel |
| Heated Seat | Yes |
| Warm Air Dryer | Yes |
| Adjustable Water Temperature | Yes |
| Adjustable Water Pressure | Yes |
| Oscillating Wash | Yes |
| Self-Cleaning Nozzle | Yes |
| Remote Control | Yes |
| Voltage | 120V |
| Nozzle Position Adjustment | Yes |
| Type | Bidet Toilet Seat |
| Power Supply | Electric |
To Next Page
