To Next PageTo Next PageWhy is my Binder 9010-0078 not working?
Your Binder Climate chamber might not be working due to several reasons. First, check the connection to the power supply. Second, the chamber fuse might have responded, so check it and replace it if needed. If it responds again, contact BINDER service. Finally, the controller could be defective, in which case you should also contact BINDER service.
What to do if Binder 9010-0078 Climate chamber set-point temperature is not reached?
If the set-point temperature isn't reached in your Binder Climate chamber, ensure the chamber door is completely closed. Also, inspect the door gasket and replace it if it’s defective. Calibrate and adjust the controller. Finally, check the power supply to ensure the voltage is correct (115V or 230V).
Why Binder 9010-0078 doesn’t heat up but controller display working?
If your Binder Climate chamber isn’t heating up, and the red heating control light is off but the controller display is working, it could be due to the timer being run off. Program the timer or switch to continuous operation. Another cause might be a defective semiconductor relay, in which case you should contact BINDER service.
What to do if Binder 9010-0078 Climate chamber isn't working and the red alarm light is on?
If your Binder Climate chamber isn't working and the red alarm pilot lamp is lit, it could be that the safety device class 2 has turned off the chamber. Let the chamber cool down and then press the RESET button. Also, the safety device class 2 might be defective, in that case contact BINDER service.
Why is my Binder 9010-0078 heating permanently?
If your Binder Climate chamber is heating permanently and not maintaining the set-point, the controller may be defective, in that case contact BINDER service. Alternatively, the controller might need calibration and adjustment.
How to fix high temperature and red alarm on Binder 9010-0078?
If the temperature inside your Binder Climate chamber is too high and the red alarm light is on, the safety device class 3.1 may have been triggered. Check the settings of the temperature set-point and of the safety device class 3.1.
Why does my Binder 9010-0078 take longer to heat up?
If you're experiencing deviations from the indicated heating-up times with your Binder Climate chamber, it might be because the chamber is fully loaded. Try loading the chamber with fewer items or allow for longer heating-up times.
Why is my Binder 9010-0078 in stand-by mode?
If your Binder Climate chamber is without function and only the green 'stand-by' LED is lit, the chamber is likely in stand-by mode. Press the ON/OFF button until the display lights up.
What to do if Binder 9010-0078 fan is not working?
If the fan in your Binder Climate chamber isn’t turning or is turning too slowly, the fan might be defective, in that case contact BINDER service.
Why does my Binder 9010-0078 controller return to normal display?
If the controller on your Binder Climate chamber returns to the Normal Display from any level, it's likely because no button was pressed for approximately 30 seconds. Repeat your entries, entering the values more rapidly.
General| Brand | Binder |
|---|---|
| Model | 9010-0078 |
| Category | Climate chamber |
| Language | English |
Provides essential safety guidelines for chamber installation and operation.
Defines the chambers' approved applications and limitations.
Outlines manufacturer's measures to prevent ignition and explosions.
Requirements for the chamber's installation site and environmental factors.
Details on connecting the chamber to the power supply.
Step-by-step guide for powering on the chamber for the first time.
How to set and view temperature set-points without using ramp functions.
How to set and view temperature set-points when using ramp functions.
Explains continuous and timer operation modes for the chamber.
Details the function and setting of the Class 2 safety device for ED and FD models.
Explains the Class 3.1 safety device for BD models and optional ED/FD.
Guidance on regular maintenance schedules and professional service.
Procedures for cleaning and decontaminating the chamber after use.
Lists common faults, their causes, and required solutions.
