What to do if I need to dry and aerate my Binder MK 720 Climate chamber after disinfection?
After using disinfectant spray in your Binder Climate chamber, allow the chamber to dry thoroughly, and ensure it is sufficiently aerated.
Why should I not empty disinfectant into drains when cleaning my Binder MK 720?
Do NOT empty the disinfectant into drains to prevent environmental damage from disinfectant disposal.
How to troubleshoot a Binder climate chamber that has no function?
If your Binder climate chamber isn't working, first check the power supply connection. Then, verify that the power supply voltage is correct. Ensure the main power switch is turned on. For MK/MKT 115, 240, and 720 models, also check and turn on the rear power switch. Inspect the chamber fuse and replace it if needed; if it fails again, contact BINDER service.
Why is there no or low refrigerating performance in my Binder climate chamber?
If your Binder climate chamber has low refrigerating performance, ensure the ambient temperature is not higher than 25 °C / 77°F and if it is, select a cooler place for installation. If the problem persists, contact BINDER service to check the compressor.
What to do if Binder climate chamber is heating permanently and not maintaining the set-point?
If your Binder climate chamber is constantly heating and not maintaining the set-point, calibrate and adjust the controller. If this doesn't resolve the issue, contact BINDER service.
What to do if Binder climate chamber doesn’t heat up when turned on and safety controller responds?
If your Binder climate chamber doesn’t heat up when turned on and the safety controller responds, acknowledge the alarm on the controller. Then, check the temperature setpoint setting. If it’s too low, select a suitable safety controller setpoint.
Why my Binder climate chamber doesn’t heat up?
If your Binder climate chamber isn’t heating up, contact BINDER service to check the heating element.
Why does my Binder climate chamber display “Preheat phase” and has no refrigerating performance?
If your Binder climate chamber shows “Preheat phase” and has no refrigerating performance, ensure the main power switch (and rear power switch for MK / MKT 115, 240, 720 models) was turned on at least one hour before operating the chamber.
What to do if acknowledging the alarm does not cancel the alarm state on Binder climate chamber?
If acknowledging the alarm on your Binder climate chamber does not cancel the alarm state, remove the cause of the alarm. If the alarm continues, contact BINDER service.
How to prevent condensation on samples in Binder climate chamber?
If you notice condensation on the samples in your Binder climate chamber, use the anti-condensation protection feature.
Provides crucial safety guidelines for installation and operation.
Defines the specific applications and limitations for the chamber's use.
Lists measures taken by the manufacturer to prevent accidents and hazards.
Explains how to enter setpoints using the "Setpoints" menu.
Describes direct setpoint entry on the normal display.
Instructions for starting a timer program (stopwatch function).
How to start a pre-existing time program.
Steps to create a new time program.
Managing existing time programs, including editing and deleting.
Managing individual sections within a time program.
Entering and modifying values for each section of a time program.
Overview of notification and alarm messages displayed by the controller.
Visual and audible indicators of the chamber's alarm state.
How to acknowledge alarms and view the list of active alarms.
Description of the built-in class 1 over-temperature protection.
Details the electronic overtemperature safety controller (class 2).
Explanation of the optional over/under temperature safety device.
Explains authorization levels and password protection mechanisms.
Procedure for logging into the controller with user credentials.
Procedures for assigning and changing user passwords.
Settings for network connectivity, including serial and Ethernet interfaces.
Performing an automated self-test for chamber functionality and fault analysis.
Guidelines for regular maintenance and service procedures.
Procedures for cleaning and decontaminating the chamber.
Provides detailed technical specifications for the MK (E4) series.
Provides detailed technical specifications for the MKT (E4) series.
General| Brand | Binder |
|---|---|
| Model | MK 720 |
| Category | Climate chamber |
| Language | English |
To Next Page
