What to do if the set-point temperature is not reached in my Binder Laboratory Equipment?
If the set-point temperature isn't reached after the specified time, there might be a few reasons. First, make sure the chamber door is completely closed. If it is, inspect the door gasket for any defects and replace it if necessary. Also, the controller might need adjustment; try calibrating it.
What causes my Binder FP 240 Laboratory Equipment chamber to heat permanently and not hold the set-point?
If your chamber is heating permanently and not holding the set-point, calibrate and adjust the controller. For other potential causes, contact Binder service.
Why are there deviations from the indicated heating-up times in my Binder Laboratory Equipment?
Deviations from the indicated heating-up times can occur if the oven is fully loaded. Try charging the oven with less material or consider allowing longer heating-up times.
Why is my Binder FP 240 chamber permanently turned off?
If the chamber is permanently turned off, first check the connection to the power supply. Ensure the correct voltage (115V or 230V) is being supplied. Also, check the chamber fuse and replace it if needed. If the fuse responds again, contact Binder service.
What to do if the red indicator lamp is lit and my Binder Laboratory Equipment chamber is permanently turned off?
If the red indicator lamp of safety device class 2 is lit and the chamber is permanently turned off, let the oven cool down and then press the RESET button. Check the temperature set-point and the setting of the safety device, and select a suitable limit value if appropriate.
What to do if my Binder Laboratory Equipment chamber doesn’t heat up, the LED is not lit, but the controller display is working?
If the chamber doesn’t heat up, the LED is not lit, and the controller display is working, contact Binder service.
What to do if my Binder FP 240 chamber doesn’t heat up, but the LED is lit?
If the chamber doesn’t heat up but the LED is lit, contact Binder service.
Why is the program duration longer than programmed on my Binder FP 240 Laboratory Equipment?
If the program duration is longer than programmed, it may be due to inappropriate tolerances. For rapid transition phases, do NOT program tolerance limits to allow maximum heating speed.
How to fix ramp temperature transitions that are only realized as steps in my Binder FP 240?
If ramp temperature transitions are only realized as steps, set the set-point programming type to “Ramp” in the User level.
Why does my Binder FP 240 program stop one section too early?
If the program stops one section too early, the program line might be incomplete. Define the end value of the desired cycle by adding an additional section with a section time of at least one minute when programming.
Harmonized denominations, symbols, signal words, and pictograms for dangerous situations.
Guidance on safe installation, operation, and usage of BINDER chambers and accessories.
Details on power connection, plugs, voltage, and electrical safety requirements.
Initial settings and display indications for the RD3 controller upon chamber startup.
Selecting between 'Ramp' and 'Step' for temperature transitions and its implications.
Procedure for entering set-points for program sections via the program editor.
Selecting a program and defining parameters like delay time and number of cycles.
Settings for menu language, program types, section duration, and set-point programming.
Step-by-step instructions for entering program data into the program editor.
Explanation of displayed alarm messages and buzzer activation/reset.
Function, setting, and checking of the Class 2 temperature safety device.
Function, setting, and checking of the optional Class 3.1 temperature safety device.
Detailed instructions for cleaning the chamber interior, exterior, and components with recommended agents.
Steps for decontaminating the chamber after exposure to hazardous substances.
Procedure for disposing of the chamber in Germany according to WEEE regulations.
Procedure for disposing of the chamber in other EU states according to WEEE regulations.
Common faults related to heating performance and their possible causes and solutions.
Troubleshooting common faults related to the program controller's operation and settings.
Detailed specifications including dimensions, capacity, temperature, and electrical data for all chamber sizes.
General| Interior Volume | 240 L |
|---|---|
| Number of Shelves | 2 |
| Max. Shelf Load | 30 kg |
| Voltage | 230 V |
| Frequency | 50/60 Hz |
| Temperature Range | 5 °C above ambient temperature to 300 °C |
| Power Consumption | 3.0 kW |
To Next Page
