To Next PageTo Next PageWhat to do if the set-point temperature is not reached in my Binder FP 53 Laboratory Equipment?
If the set-point temperature isn't reached after the specified time, there might be a few reasons. First, make sure the chamber door is completely closed. If it is, inspect the door gasket for any defects and replace it if necessary. Also, the controller might need adjustment; try calibrating it.
What causes my Binder FP 53 Laboratory Equipment chamber to heat permanently and not hold the set-point?
If your chamber is heating permanently and not holding the set-point, calibrate and adjust the controller. For other potential causes, contact Binder service.
Why are there deviations from the indicated heating-up times in my Binder Laboratory Equipment?
Deviations from the indicated heating-up times can occur if the oven is fully loaded. Try charging the oven with less material or consider allowing longer heating-up times.
Why is my Binder FP 53 chamber permanently turned off?
If the chamber is permanently turned off, first check the connection to the power supply. Ensure the correct voltage (115V or 230V) is being supplied. Also, check the chamber fuse and replace it if needed. If the fuse responds again, contact Binder service.
What to do if the red indicator lamp is lit and my Binder Laboratory Equipment chamber is permanently turned off?
If the red indicator lamp of safety device class 2 is lit and the chamber is permanently turned off, let the oven cool down and then press the RESET button. Check the temperature set-point and the setting of the safety device, and select a suitable limit value if appropriate.
What to do if my Binder FP 53 Laboratory Equipment chamber doesn’t heat up, the LED is not lit, but the controller display is working?
If the chamber doesn’t heat up, the LED is not lit, and the controller display is working, contact Binder service.
What to do if my Binder FP 53 chamber doesn’t heat up, but the LED is lit?
If the chamber doesn’t heat up but the LED is lit, contact Binder service.
Why is the program duration longer than programmed on my Binder FP 53 Laboratory Equipment?
If the program duration is longer than programmed, it may be due to inappropriate tolerances. For rapid transition phases, do NOT program tolerance limits to allow maximum heating speed.
How to fix ramp temperature transitions that are only realized as steps in my Binder FP 53?
If ramp temperature transitions are only realized as steps, set the set-point programming type to “Ramp” in the User level.
Why does my Binder FP 53 Laboratory Equipment program stop one section too early?
If the program stops one section too early, the program line might be incomplete. Define the end value of the desired cycle by adding an additional section with a section time of at least one minute when programming.
Crucial safety guidelines for installing, operating, and maintaining the chamber.
Defines approved applications and operational limits for the equipment.
Procedures and precautions for safely moving and transporting the chamber.
Specifies requirements for the installation location and environmental conditions.
Steps for connecting the chamber to the power supply, including voltage checks.
Explains how to enter set-points for temperature and fan speed in fixed value mode.
Step-by-step guide for entering temperature and fan speed values.
Explains selection between gradual (ramp) and sudden (step) temperature transitions.
Guides on entering temperature, time, and fan speed for program sections.
Steps for selecting, starting, and terminating programmed sequences.
Settings for program types, section duration, ramp/step, tolerance, and week timer.
Provides a step-by-step guide to implementing the weekly temperature program.
Explains displayed alarm messages and buzzer functions.
Details on the function, operation, and checking of the Class 2 safety device.
Procedures for cleaning chamber interior, exterior, and decontamination.
Addresses issues related to chamber heating and temperature control.
Solutions for problems with the program controller and its functions.
Comprehensive table of chamber dimensions, performance, and electrical specifications.
Crucial safety guidelines for installing, operating, and maintaining the chamber.
Defines approved applications and operational limits for the equipment.
Procedures and precautions for safely moving and transporting the chamber.
Specifies requirements for the installation location and environmental conditions.
Steps for connecting the chamber to the power supply, including voltage checks.
Explains how to enter set-points for temperature and fan speed in fixed value mode.
Step-by-step guide for entering temperature and fan speed values.
Explains selection between gradual (ramp) and sudden (step) temperature transitions.
Guides on entering temperature, time, and fan speed for program sections.
Steps for selecting, starting, and terminating programmed sequences.
Settings for program types, section duration, ramp/step, tolerance, and week timer.
Provides a step-by-step guide to implementing the weekly temperature program.
Explains displayed alarm messages and buzzer functions.
Details on the function, operation, and checking of the Class 2 safety device.
Procedures for cleaning chamber interior, exterior, and decontamination.
Addresses issues related to chamber heating and temperature control.
Solutions for problems with the program controller and its functions.
Comprehensive table of chamber dimensions, performance, and electrical specifications.
General| Brand | Binder |
|---|---|
| Model | FP 53 |
| Category | Laboratory Equipment |
| Language | English |
