What to do if Binder FD 260 Laboratory Equipment chamber has no function?
First, check the connection to the power supply. If that's not the issue, the overtemperature protective device class 1 might have turned off the chamber. Disconnect the chamber from the power supply for at least 10 seconds and let it cool down. If the device responds again, further assistance is needed.
Why is the set-point temperature not reached in my Binder FD 260 after the specified time?
Several factors could be the reason. Make sure the chamber door is completely closed and that the door gasket isn't defective (replace if needed). The controller may also need calibration and adjustment. Finally, verify the power supply for the correct voltage.
What to do if Binder FD 260 chamber doesn’t heat up but the controller display is working?
The timer might have run off. Try re-programming the timer or turning it off.
Why is my Binder FD 260 Laboratory Equipment chamber heating permanently and not holding the set-point?
The controller may not be adjusted, so calibrate and adjust it. If the issue persists, the controller might be defective and further assistance is needed.
What to do if my ED, FD, or FED Binder FD 260 Laboratory Equipment chamber has no function and shows the alarm message “!TLim”?
The safety device class 2 has likely turned off the chamber. Allow the chamber to cool down. Check the temperature set-point and the settings of the safety device class 2. If appropriate, select a suitable limit value. If the issue persists, further assistance is needed.
What to do if my Binder Laboratory Equipment chamber has no function?
First, check the connection to the power supply. If the overtemperature protective device class 1 has turned off the chamber, disconnect the chamber from the power supply for at least 10 seconds and let it cool down. If the device responds again, further assistance is needed.
What to do if my ED, FD, FED Binder Laboratory Equipment chamber has no function and shows alarm message “!TLim”?
This alarm indicates that safety device class 2 has turned off the chamber. Allow the chamber to cool down. Check the settings of the temperature set-point and the safety device class 2, and select a suitable limit value if needed.
What to do if my Binder Laboratory Equipment chamber doesn’t heat up and there is no heating icon in the display, but controller display is working?
The timer may have run off. Try re-programming the timer or turn it off.
What to do if my BD, BF Binder Laboratory Equipment displays alarm message “!TProt”?
The alarm message “!TProt” indicates that safety device class 3.1 has responded. Check the settings of the temperature set-point and of the safety device class 3.1.
What to do if my Binder FD 260 Laboratory Equipment chamber is heating permanently, and the set-point is not held?
The controller may not be adjusted correctly. Calibrate and adjust the controller.
Requirements for qualified personnel for chamber installation, testing, and operation.
Guidelines for handling and understanding the operating manual for safe chamber use.
Explanation of safety signal words, alert symbols, and pictograms used in the manual.
Essential safety guidelines for installation and operation, including hazards.
Defines the proper use of the chambers and outlines prohibited applications.
Lists potential misuses of the chamber and associated risks.
Identifies unavoidable risks and necessary precautions during operation and maintenance.
Description of the control panel, display, buttons, and USB interface.
Detailed procedures and warnings for safely lifting and transporting the chamber.
Requirements for installation site, ambient conditions, and minimum distances.
Details on connecting the chamber to the power supply, including specifications.
Guidelines for loading the chamber, including maximum load limits and rack orientation.
Explanation of controller buttons, status symbols, and display elements.
How to set desired temperature and fan speed values for the chamber.
Explanation of the class 1 safety device that turns off heating when temperature limits are exceeded.
Details on adjustable safety controllers (class 2 and 3.1) for temperature protection.
How to set the limit temperature for the safety controller to ensure protection.
Information on alarm messages, buzzer sounds, and steps to reset alarms.
Instructions for connecting a USB stick and initiating data recording.
Steps to stop the active data recording process.
Step-by-step guide for cleaning the chamber interior and exterior surfaces.
Procedures for decontaminating the chamber from hazardous substances.
Details on recommended maintenance intervals and service procedures.
Guide to diagnosing and resolving common faults and shortcomings.
Detailed technical specifications for BD series chambers, including dimensions and electrical data.
Detailed technical specifications for BF series chambers, including dimensions and electrical data.
Detailed technical specifications for ED series chambers, including dimensions and electrical data.
Detailed technical specifications for FD series chambers, including dimensions and electrical data.
Detailed technical specifications for FED series chambers, including dimensions and electrical data.
General| Temperature Accuracy | ± 0.3 °C |
|---|---|
| Power Supply | 230 V, 50/60 Hz |
| Type | Drying oven |
| Temperature Range | 5 °C above ambient temperature to 300 °C |
| Interior Volume | 260 L |
To Next Page
