To Next PageTo Next PageWhat to do if Binder ED 260 Laboratory Equipment chamber has no function?
First, check the connection to the power supply. If that's not the issue, the overtemperature protective device class 1 might have turned off the chamber. Disconnect the chamber from the power supply for at least 10 seconds and let it cool down. If the device responds again, further assistance is needed.
Why is the set-point temperature not reached in my Binder ED 260 Laboratory Equipment after the specified time?
Several factors could be the reason. Make sure the chamber door is completely closed and that the door gasket isn't defective (replace if needed). The controller may also need calibration and adjustment. Finally, verify the power supply for the correct voltage.
What to do if Binder ED 260 chamber doesn’t heat up but the controller display is working?
The timer might have run off. Try re-programming the timer or turning it off.
Why is my Binder ED 260 chamber heating permanently and not holding the set-point?
The controller may not be adjusted, so calibrate and adjust it. If the issue persists, the controller might be defective and further assistance is needed.
What to do if my ED, FD, or FED Binder ED 260 chamber has no function and shows the alarm message “!TLim”?
The safety device class 2 has likely turned off the chamber. Allow the chamber to cool down. Check the temperature set-point and the settings of the safety device class 2. If appropriate, select a suitable limit value. If the issue persists, further assistance is needed.
What to do if my Binder ED 260 chamber has no function?
First, check the connection to the power supply. If the overtemperature protective device class 1 has turned off the chamber, disconnect the chamber from the power supply for at least 10 seconds and let it cool down. If the device responds again, further assistance is needed.
What to do if my ED, FD, FED Binder ED 260 chamber has no function and shows alarm message “!TLim”?
This alarm indicates that safety device class 2 has turned off the chamber. Allow the chamber to cool down. Check the settings of the temperature set-point and the safety device class 2, and select a suitable limit value if needed.
What to do if my Binder Laboratory Equipment chamber doesn’t heat up and there is no heating icon in the display, but controller display is working?
The timer may have run off. Try re-programming the timer or turn it off.
What to do if my BD, BF Binder ED 260 Laboratory Equipment displays alarm message “!TProt”?
The alarm message “!TProt” indicates that safety device class 3.1 has responded. Check the settings of the temperature set-point and of the safety device class 3.1.
What to do if my Binder ED 260 Laboratory Equipment chamber is heating permanently, and the set-point is not held?
The controller may not be adjusted correctly. Calibrate and adjust the controller.
Requirement for qualified personnel, manual usage, general safety instructions, intended use, and residual risks.
Chamber overview, components, and controller operations including settings.
Unpacking, lifting, transportation, site requirements, and electrical connection.
Initial steps to power on, load, and operate the chamber.
Explanation of protective devices, safety controllers, and alarm handling procedures.
Guide to using timer functions and programming temperature ramps.
How to record data via USB and configure network settings.
Instructions for cleaning, decontaminating, and performing regular maintenance.
Guide to resolve common faults and procedures for returning equipment.
Guidelines for proper disposal of the chamber according to regulations.
Detailed technical data, dimensions, and specifications for various models.
Official EU and UL compliance statements and conformity certificates.
Forms for declaring absence of hazardous substances and requesting return authorization.
Requirement for qualified personnel, manual usage, general safety instructions, intended use, and residual risks.
Chamber overview, components, and controller operations including settings.
Unpacking, lifting, transportation, site requirements, and electrical connection.
Initial steps to power on, load, and operate the chamber.
Explanation of protective devices, safety controllers, and alarm handling procedures.
Guide to using timer functions and programming temperature ramps.
How to record data via USB and configure network settings.
Instructions for cleaning, decontaminating, and performing regular maintenance.
Guide to resolve common faults and procedures for returning equipment.
Guidelines for proper disposal of the chamber according to regulations.
Detailed technical data, dimensions, and specifications for various models.
Official EU and UL compliance statements and conformity certificates.
Forms for declaring absence of hazardous substances and requesting return authorization.
General| Brand | Binder |
|---|---|
| Model | ED 260 |
| Category | Laboratory Equipment |
| Language | English |
