To Next PageTo Next PageWhat to do if Binder BD 260 Laboratory Equipment chamber has no function?
First, check the connection to the power supply. If that's not the issue, the overtemperature protective device class 1 might have turned off the chamber. Disconnect the chamber from the power supply for at least 10 seconds and let it cool down. If the device responds again, further assistance is needed.
Why is the set-point temperature not reached in my Binder Laboratory Equipment after the specified time?
Several factors could be the reason. Make sure the chamber door is completely closed and that the door gasket isn't defective (replace if needed). The controller may also need calibration and adjustment. Finally, verify the power supply for the correct voltage.
What to do if Binder BD 260 chamber doesn’t heat up but the controller display is working?
The timer might have run off. Try re-programming the timer or turning it off.
Why is my Binder BD 260 chamber heating permanently and not holding the set-point?
The controller may not be adjusted, so calibrate and adjust it. If the issue persists, the controller might be defective and further assistance is needed.
What to do if my ED, FD, or FED Binder Laboratory Equipment chamber has no function and shows the alarm message “!TLim”?
The safety device class 2 has likely turned off the chamber. Allow the chamber to cool down. Check the temperature set-point and the settings of the safety device class 2. If appropriate, select a suitable limit value. If the issue persists, further assistance is needed.
What to do if my Binder BD 260 Laboratory Equipment chamber has no function?
First, check the connection to the power supply. If the overtemperature protective device class 1 has turned off the chamber, disconnect the chamber from the power supply for at least 10 seconds and let it cool down. If the device responds again, further assistance is needed.
What to do if my ED, FD, FED Binder Laboratory Equipment chamber has no function and shows alarm message “!TLim”?
This alarm indicates that safety device class 2 has turned off the chamber. Allow the chamber to cool down. Check the settings of the temperature set-point and the safety device class 2, and select a suitable limit value if needed.
What to do if my Binder BD 260 chamber doesn’t heat up and there is no heating icon in the display, but controller display is working?
The timer may have run off. Try re-programming the timer or turn it off.
What to do if my BD, BF Binder BD 260 Laboratory Equipment displays alarm message “!TProt”?
The alarm message “!TProt” indicates that safety device class 3.1 has responded. Check the settings of the temperature set-point and of the safety device class 3.1.
What to do if my Binder BD 260 chamber is heating permanently, and the set-point is not held?
The controller may not be adjusted correctly. Calibrate and adjust the controller.
Ensures chambers are installed, tested, and operated by qualified and trained personnel.
Instructions for correct operation, including safety precautions for injury prevention.
Details on the chamber's identification, specifications, and manufacturer information.
Guidelines for installation, operation, and warnings regarding ventilation and explosive areas.
Description of the controller display, buttons, and USB interface.
Safety precautions and methods for lifting and transporting the chamber.
Requirements for the installation site, including ventilation and minimum distances.
Details on power plugs, voltage, current type, and fuses for various models.
Step-by-step guide to change the controller's display language.
Procedure for configuring the chamber's date and time settings.
How to input and adjust temperature and fan speed set-points.
Description of the safety device that turns off heating when temperature limits are exceeded.
Details on Class 2 (temperature limiter) and Class 3.1 (temperature protection) safety controllers.
Procedure for entering the safety controller's limit temperature value.
How to handle alarm messages and reset the system after an overtemperature event.
Setting run-time, fan operation, and turning off the timer function.
Setting run-time, fan operation, and set-point based on temperature.
Steps to connect a USB stick and begin recording chamber data.
Instructions for cleaning interior/exterior surfaces using recommended agents.
Methods for decontaminating the chamber after exposure to hazardous substances.
Guides for identifying and resolving common chamber faults without technical intervention.
Comprehensive technical specifications for BINDER BD models.
Comprehensive technical specifications for BINDER BF models.
Comprehensive technical specifications for BINDER ED models.
Comprehensive technical specifications for BINDER FD models.
Comprehensive technical specifications for BINDER FED models.
Ensures chambers are installed, tested, and operated by qualified and trained personnel.
Instructions for correct operation, including safety precautions for injury prevention.
Details on the chamber's identification, specifications, and manufacturer information.
Guidelines for installation, operation, and warnings regarding ventilation and explosive areas.
Description of the controller display, buttons, and USB interface.
Safety precautions and methods for lifting and transporting the chamber.
Requirements for the installation site, including ventilation and minimum distances.
Details on power plugs, voltage, current type, and fuses for various models.
Step-by-step guide to change the controller's display language.
Procedure for configuring the chamber's date and time settings.
How to input and adjust temperature and fan speed set-points.
Description of the safety device that turns off heating when temperature limits are exceeded.
Details on Class 2 (temperature limiter) and Class 3.1 (temperature protection) safety controllers.
Procedure for entering the safety controller's limit temperature value.
How to handle alarm messages and reset the system after an overtemperature event.
Setting run-time, fan operation, and turning off the timer function.
Setting run-time, fan operation, and set-point based on temperature.
Steps to connect a USB stick and begin recording chamber data.
Instructions for cleaning interior/exterior surfaces using recommended agents.
Methods for decontaminating the chamber after exposure to hazardous substances.
Guides for identifying and resolving common chamber faults without technical intervention.
Comprehensive technical specifications for BINDER BD models.
Comprehensive technical specifications for BINDER BF models.
Comprehensive technical specifications for BINDER ED models.
Comprehensive technical specifications for BINDER FD models.
Comprehensive technical specifications for BINDER FED models.
General| Temperature Accuracy | ±0.3°C |
|---|---|
| Max. Load per Shelf | 30 kg |
| Voltage | 230 V |
| Frequency | 50/60 Hz |
| Type | Drying Oven |
| Temperature Range | 5 °C above ambient temperature to 300 °C |
| Shelves (std./max.) | 2 / |
| Shelves | 2 |
| Control System | Microprocessor |
| Display | Digital |
