To Next PageTo Next Page
Need help?Do you have a question about the Binder BD056-230V and is the answer not in the manual?
General information and disclaimer regarding the operating manual's content.
Explains safety definitions, signal words, symbols, and hazard message panel structure.
Illustrates the locations of various safety labels on the chamber unit.
Describes the information presented on the device's identification type plate.
Essential safety guidelines for chamber installation, operation, and maintenance.
Defines the approved uses and explicitly prohibited applications for the chambers.
General overview of chamber design, features, and main components.
Details the controller, display, and interface panel of the chamber.
Identifies the main power switch for ED, FD, and FED 720 models.
Steps for unpacking, checking for damage, and verifying delivery completeness.
Instructions for safely lifting, moving, and transporting the chamber.
Guidelines for proper storage conditions and temperature ranges.
Requirements for the installation location, ventilation, and environmental parameters.
Instructions for installing tilt protection for chambers with windows.
Detailed guidance for connecting the chamber to the power supply.
Procedures for connecting the chamber's exhaust to an external system.
Explains how opening the chamber door affects heating and fan operation.
Identifies controller buttons, status symbols, and display modes.
Shows the standard display configurations for chambers.
Step-by-step guide for changing the controller's interface language.
Instructions for configuring the chamber's internal clock.
Procedure for switching between Celsius and Fahrenheit temperature units.
Guide for entering and adjusting temperature and fan speed set-points.
Specific rules for temperature set-points in two-door ED, FD, FED 720 models.
Instructions for controlling the air flap for adjusting fresh air entry.
Steps for setting and changing passwords for user and controller access.
Details the primary safety device that turns off heating upon overtemperature.
Explains the safety controller's role as a temperature limiter or protector.
Guide for configuring the safety controller's limit temperature.
How to interpret alarms and the steps to take for reset and recovery.
Recommendation to periodically check the safety controller's functionality.
Instructions for activating or deactivating the audible over-temperature alarm.
Overview of available timer functions: Delayed Off, Temp-Dependent Delayed Off, Delayed On.
Setting up, activating, and managing the 'Delayed Off' timer function.
Setting up and managing the temp-dependent 'Delayed Off' timer.
Setting up and managing the 'Delayed On' timer function.
An example demonstrating temperature programming using timer functions.
Explains the purpose and basic principles of temperature ramp programming.
Step-by-step guide to setting up and viewing temperature ramps.
How to display the effective ramp set-point and change the target set-point.
Procedure for deactivating the temperature ramp function.
Steps to initiate data recording using a USB stick.
Procedures for stopping the data recording process.
Guide for configuring network settings via the Ethernet interface.
Details on the optional PC software for chamber control and data management.
Information on optional data logger kits for long-term temperature measurement.
Description of the optional sensor for measuring object temperature.
Explains the optional analog output for transmitting temperature data.
Details the optional internal socket for connecting devices inside the chamber.
Description of the optional HEPA filter for cleaning incoming fresh air.
Information on the optional gas-tight chamber version for reduced gas loss.
Details on connecting inert gas for the mostly gas-tight version.
Guidelines for routine maintenance and recommended service schedules.
Procedures for cleaning surfaces and decontaminating the chamber.
Process for returning a chamber for repair, including RMA number requirements.
Guidance on the proper disposal of packaging elements.
Instructions for safely taking the chamber out of service before disposal.
Procedures for disposing of the chamber according to German law.
Disposal procedures for EU countries outside of Germany.
Guidelines for chamber disposal in countries outside the European Union.
Lists common temperature and controller issues with their solutions.
Information regarding the chamber's factory calibration and adjustment.
Explains how the usable volume is determined and its implications.
Describes the protection systems against over-current conditions.
Comprehensive technical specifications for BD incubators.
Comprehensive technical specifications for BF incubators.
Comprehensive technical specifications for ED drying and heating ovens.
Comprehensive technical specifications for FD drying and heating ovens.
Comprehensive technical specifications for FED drying and heating ovens.
Lists standard equipment and optional features available for the chambers.
Catalog of available accessories and spare parts with article numbers.
Detailed dimensional drawings for chambers of size 56.
Detailed dimensional drawings for chambers of size 115.
Detailed dimensional drawings for chambers of size 260.
Detailed dimensional drawings for chambers of size 720.
Official EU conformity statement for BD series chambers.
Official EU conformity statement for BF series chambers.
Official EU conformity statement for ED series ovens.
Official EU conformity statement for FD series ovens.
Official EU conformity statement for FED series ovens.
Form for clearing contamination for returns from outside USA/Canada.
Form for clearing contamination for returns from USA/Canada.
General information and disclaimer regarding the operating manual's content.
Explains safety definitions, signal words, symbols, and hazard message panel structure.
Illustrates the locations of various safety labels on the chamber unit.
Describes the information presented on the device's identification type plate.
Essential safety guidelines for chamber installation, operation, and maintenance.
Defines the approved uses and explicitly prohibited applications for the chambers.
General overview of chamber design, features, and main components.
Details the controller, display, and interface panel of the chamber.
Identifies the main power switch for ED, FD, and FED 720 models.
Steps for unpacking, checking for damage, and verifying delivery completeness.
Instructions for safely lifting, moving, and transporting the chamber.
Guidelines for proper storage conditions and temperature ranges.
Requirements for the installation location, ventilation, and environmental parameters.
Instructions for installing tilt protection for chambers with windows.
Detailed guidance for connecting the chamber to the power supply.
Procedures for connecting the chamber's exhaust to an external system.
Explains how opening the chamber door affects heating and fan operation.
Identifies controller buttons, status symbols, and display modes.
Shows the standard display configurations for chambers.
Step-by-step guide for changing the controller's interface language.
Instructions for configuring the chamber's internal clock.
Procedure for switching between Celsius and Fahrenheit temperature units.
Guide for entering and adjusting temperature and fan speed set-points.
Specific rules for temperature set-points in two-door ED, FD, FED 720 models.
Instructions for controlling the air flap for adjusting fresh air entry.
Steps for setting and changing passwords for user and controller access.
Details the primary safety device that turns off heating upon overtemperature.
Explains the safety controller's role as a temperature limiter or protector.
Guide for configuring the safety controller's limit temperature.
How to interpret alarms and the steps to take for reset and recovery.
Recommendation to periodically check the safety controller's functionality.
Instructions for activating or deactivating the audible over-temperature alarm.
Overview of available timer functions: Delayed Off, Temp-Dependent Delayed Off, Delayed On.
Setting up, activating, and managing the 'Delayed Off' timer function.
Setting up and managing the temp-dependent 'Delayed Off' timer.
Setting up and managing the 'Delayed On' timer function.
An example demonstrating temperature programming using timer functions.
Explains the purpose and basic principles of temperature ramp programming.
Step-by-step guide to setting up and viewing temperature ramps.
How to display the effective ramp set-point and change the target set-point.
Procedure for deactivating the temperature ramp function.
Steps to initiate data recording using a USB stick.
Procedures for stopping the data recording process.
Guide for configuring network settings via the Ethernet interface.
Details on the optional PC software for chamber control and data management.
Information on optional data logger kits for long-term temperature measurement.
Description of the optional sensor for measuring object temperature.
Explains the optional analog output for transmitting temperature data.
Details the optional internal socket for connecting devices inside the chamber.
Description of the optional HEPA filter for cleaning incoming fresh air.
Information on the optional gas-tight chamber version for reduced gas loss.
Details on connecting inert gas for the mostly gas-tight version.
Guidelines for routine maintenance and recommended service schedules.
Procedures for cleaning surfaces and decontaminating the chamber.
Process for returning a chamber for repair, including RMA number requirements.
Guidance on the proper disposal of packaging elements.
Instructions for safely taking the chamber out of service before disposal.
Procedures for disposing of the chamber according to German law.
Disposal procedures for EU countries outside of Germany.
Guidelines for chamber disposal in countries outside the European Union.
Lists common temperature and controller issues with their solutions.
Information regarding the chamber's factory calibration and adjustment.
Explains how the usable volume is determined and its implications.
Describes the protection systems against over-current conditions.
Comprehensive technical specifications for BD incubators.
Comprehensive technical specifications for BF incubators.
Comprehensive technical specifications for ED drying and heating ovens.
Comprehensive technical specifications for FD drying and heating ovens.
Comprehensive technical specifications for FED drying and heating ovens.
Lists standard equipment and optional features available for the chambers.
Catalog of available accessories and spare parts with article numbers.
Detailed dimensional drawings for chambers of size 56.
Detailed dimensional drawings for chambers of size 115.
Detailed dimensional drawings for chambers of size 260.
Detailed dimensional drawings for chambers of size 720.
Official EU conformity statement for BD series chambers.
Official EU conformity statement for BF series chambers.
Official EU conformity statement for ED series ovens.
Official EU conformity statement for FD series ovens.
Official EU conformity statement for FED series ovens.
Form for clearing contamination for returns from outside USA/Canada.
Form for clearing contamination for returns from USA/Canada.
General| Model | BD056-230V |
|---|---|
| Voltage | 230V |
| Temperature Range | Ambient +5°C to 300°C |
| Capacity | 53 liters |
| Interior Material | Stainless steel |
| Type | Drying Oven |
| Control Type | Microprocessor controller with LCD |
| Interior Dimensions | 400 x 330 x 400 mm |
| Power Consumption | 1.2 kW |
