What to do if Binder BF 260 chamber has no function?
First, check the connection to the power supply. If that's not the issue, the overtemperature protective device class 1 might have turned off the chamber. Disconnect the chamber from the power supply for at least 10 seconds and let it cool down. If the device responds again, further assistance is needed.
Why is the set-point temperature not reached in my Binder BF 260 after the specified time?
Several factors could be the reason. Make sure the chamber door is completely closed and that the door gasket isn't defective (replace if needed). The controller may also need calibration and adjustment. Finally, verify the power supply for the correct voltage.
What to do if Binder BF 260 chamber doesn’t heat up but the controller display is working?
The timer might have run off. Try re-programming the timer or turning it off.
Why is my Binder BF 260 Laboratory Equipment chamber heating permanently and not holding the set-point?
The controller may not be adjusted, so calibrate and adjust it. If the issue persists, the controller might be defective and further assistance is needed.
What to do if my ED, FD, or FED Binder BF 260 Laboratory Equipment chamber has no function and shows the alarm message “!TLim”?
The safety device class 2 has likely turned off the chamber. Allow the chamber to cool down. Check the temperature set-point and the settings of the safety device class 2. If appropriate, select a suitable limit value. If the issue persists, further assistance is needed.
What to do if my Binder BF 260 Laboratory Equipment chamber has no function?
First, check the connection to the power supply. If the overtemperature protective device class 1 has turned off the chamber, disconnect the chamber from the power supply for at least 10 seconds and let it cool down. If the device responds again, further assistance is needed.
What to do if my ED, FD, FED Binder Laboratory Equipment chamber has no function and shows alarm message “!TLim”?
This alarm indicates that safety device class 2 has turned off the chamber. Allow the chamber to cool down. Check the settings of the temperature set-point and the safety device class 2, and select a suitable limit value if needed.
What to do if my Binder BF 260 chamber doesn’t heat up and there is no heating icon in the display, but controller display is working?
The timer may have run off. Try re-programming the timer or turn it off.
What to do if my BD, BF Binder BF 260 displays alarm message “!TProt”?
The alarm message “!TProt” indicates that safety device class 3.1 has responded. Check the settings of the temperature set-point and of the safety device class 3.1.
What to do if my Binder Laboratory Equipment chamber is heating permanently, and the set-point is not held?
The controller may not be adjusted correctly. Calibrate and adjust the controller.
Ensures trained staff operate the chamber safely and correctly.
Covers signal words, symbols, and hazard communication for safe operation.
Defines proper usage, identifies foreseeable misuse, and outlines residual risks.
Details on connecting the chamber to the power supply, including voltage and fuse info.
Steps for entering set-points for temperature and fan speed.
Explains the Class 1 protective device and its cut-off temperatures.
Details Class 2 and 3.1 controllers, set-point adjustment, and alarm management.
Covers selecting and configuring Delayed Off, Temp. Dependent Delayed Off, and Delayed On timers.
Guides on setting IP address, subnet mask, gateway, and MAC address.
Methods for decontaminating the chamber from hazardous substances.
Guidelines for regular maintenance and service requirements.
Guide to diagnose and resolve typical chamber malfunctions.
Procedures for decommissioning and disposing of the chamber in various regions.
General| Temperature Range | Ambient +5°C to 300°C |
|---|---|
| Voltage | 230 V |
| Shelves | 2 |
| Number of Shelves (Standard/Max) | 2 |
| Display | LCD |
| Rated Voltage | 230 V |
| Power Consumption | 1600 W |
To Next Page
