To Next PageTo Next PageWhat to do if Binder ED 56 chamber has no function?
First, check the connection to the power supply. If that's not the issue, the overtemperature protective device class 1 might have turned off the chamber. Disconnect the chamber from the power supply for at least 10 seconds and let it cool down. If the device responds again, further assistance is needed.
Why is the set-point temperature not reached in my Binder ED 56 Laboratory Equipment after the specified time?
Several factors could be the reason. Make sure the chamber door is completely closed and that the door gasket isn't defective (replace if needed). The controller may also need calibration and adjustment. Finally, verify the power supply for the correct voltage.
What to do if Binder Laboratory Equipment chamber doesn’t heat up but the controller display is working?
The timer might have run off. Try re-programming the timer or turning it off.
Why is my Binder Laboratory Equipment chamber heating permanently and not holding the set-point?
The controller may not be adjusted, so calibrate and adjust it. If the issue persists, the controller might be defective and further assistance is needed.
What to do if my ED, FD, or FED Binder ED 56 Laboratory Equipment chamber has no function and shows the alarm message “!TLim”?
The safety device class 2 has likely turned off the chamber. Allow the chamber to cool down. Check the temperature set-point and the settings of the safety device class 2. If appropriate, select a suitable limit value. If the issue persists, further assistance is needed.
What to do if my Binder ED 56 chamber has no function?
First, check the connection to the power supply. If the overtemperature protective device class 1 has turned off the chamber, disconnect the chamber from the power supply for at least 10 seconds and let it cool down. If the device responds again, further assistance is needed.
What to do if my ED, FD, FED Binder ED 56 chamber has no function and shows alarm message “!TLim”?
This alarm indicates that safety device class 2 has turned off the chamber. Allow the chamber to cool down. Check the settings of the temperature set-point and the safety device class 2, and select a suitable limit value if needed.
What to do if my Binder ED 56 Laboratory Equipment chamber doesn’t heat up and there is no heating icon in the display, but controller display is working?
The timer may have run off. Try re-programming the timer or turn it off.
What to do if my BD, BF Binder ED 56 Laboratory Equipment displays alarm message “!TProt”?
The alarm message “!TProt” indicates that safety device class 3.1 has responded. Check the settings of the temperature set-point and of the safety device class 3.1.
What to do if my Binder Laboratory Equipment chamber is heating permanently, and the set-point is not held?
The controller may not be adjusted correctly. Calibrate and adjust the controller.
Proper applications, foreseeable misuse, and residual risks of the chamber.
Detailed information on electrical connections, including cables and fuses.
How to set temperature/fan speed and adjust the air flap position.
Procedure for setting or changing user and controller access passwords.
Description of Class 1 protective device and Class 2/3.1 safety controllers.
Procedures for handling alarms and checking safety controller functionality.
Explanation of temperature ramps and step-by-step guide to setting them up.
Steps to initiate and stop data recording using a USB stick.
Procedures for configuring network parameters like MAC address, DHCP, IP, Subnet, and Gateway.
Procedures and recommended agents for cleaning chamber surfaces and components.
Methods for decontaminating the chamber after exposure to hazardous substances.
Requirements for personnel and recommended schedule for regular maintenance.
Guide to resolving common faults and procedures for returning the chamber.
Proper applications, foreseeable misuse, and residual risks of the chamber.
Detailed information on electrical connections, including cables and fuses.
How to set temperature/fan speed and adjust the air flap position.
Procedure for setting or changing user and controller access passwords.
Description of Class 1 protective device and Class 2/3.1 safety controllers.
Procedures for handling alarms and checking safety controller functionality.
Explanation of temperature ramps and step-by-step guide to setting them up.
Steps to initiate and stop data recording using a USB stick.
Procedures for configuring network parameters like MAC address, DHCP, IP, Subnet, and Gateway.
Procedures and recommended agents for cleaning chamber surfaces and components.
Methods for decontaminating the chamber after exposure to hazardous substances.
Requirements for personnel and recommended schedule for regular maintenance.
Guide to resolving common faults and procedures for returning the chamber.
General| Brand | Binder |
|---|---|
| Model | ED 56 |
| Category | Laboratory Equipment |
| Language | English |
