To Next PageTo Next PageWhy are there deviations from the indicated heating-up times in my Binder Laboratory Equipment?
The chamber might be fully loaded. Try loading the chamber with fewer items or consider allowing longer heating-up times.
Why is the set-point temperature not reached in my Binder Laboratory Equipment after the specified time?
Several factors could be the reason. Make sure the chamber door is completely closed and that the door gasket isn't defective (replace if needed). The controller may also need calibration and adjustment. Finally, verify the power supply for the correct voltage.
What to do if Binder Laboratory Equipment chamber doesn’t heat up but the controller display is working?
The timer might have run off. Try re-programming the timer or turning it off.
Why is my Binder Laboratory Equipment chamber heating permanently and not holding the set-point?
The controller may not be adjusted, so calibrate and adjust it. If the issue persists, the controller might be defective and further assistance is needed.
What to do if the Binder ED 115 chamber has no function and the standby icon is displayed?
The chamber is likely in standby mode. Press down the standby button until the display lights up.
What to do if Binder Climate chamber fan is not working?
If the fan in your Binder Climate chamber isn’t turning or is turning too slowly, the fan might be defective, in that case contact BINDER service.
Why does my Binder Climate chamber take longer to heat up?
If you're experiencing deviations from the indicated heating-up times with your Binder Climate chamber, it might be because the chamber is fully loaded. Try loading the chamber with fewer items or allow for longer heating-up times.
Why is my Binder Climate chamber in stand-by mode?
If your Binder Climate chamber is without function and only the green 'stand-by' LED is lit, the chamber is likely in stand-by mode. Press the ON/OFF button until the display lights up.
Why is my Binder Climate chamber not working?
Your Binder Climate chamber might not be working due to several reasons. First, check the connection to the power supply. Second, the chamber fuse might have responded, so check it and replace it if needed. If it responds again, contact BINDER service. Finally, the controller could be defective, in which case you should also contact BINDER service.
What to do if my Binder ED 115 chamber is heating permanently, and the set-point is not held?
The controller may not be adjusted correctly. Calibrate and adjust the controller.
Qualification requirements for personnel operating the chamber.
Important safety guidelines for installation and operation.
Description of the chamber's proper applications and limitations.
Instructions for safely moving and transporting the chamber.
Requirements for the installation site and environmental conditions.
Detailed instructions and data for connecting the chamber electrically.
Description of the controller buttons, symbols, and display.
How to set temperature and fan speed values.
Procedure for setting user and controller access passwords.
Description of the class 1 overtemperature protection device.
Details on the adjustable electronic safety controller and its classes.
How to set the limit temperature for the safety controller.
How to handle alarm messages and system responses.
Overview of available timer functions and their operation.
Detailed steps for setting the "Delayed Off" timer function.
Steps for setting the temperature-dependent delayed off timer.
Setting timer run-time, fan, and set-point for temperature-dependent timer.
Steps for setting the "Delayed On" timer function.
Setting timer run-time and fan speed for Delayed On timer.
How to program and view ramp function settings.
Viewing and modifying the ramp set-point.
Instructions on how to initiate data recording via USB.
Instructions on how to stop data recording via USB.
How to manually set the chamber's IP address.
Procedures and recommended agents for cleaning the chamber.
Methods for decontaminating the chamber after exposure to hazardous substances.
Overview of maintenance, service, and personnel requirements.
Recommended intervals and procedures for maintenance.
Common faults and their solutions for operating personnel.
Description of overcurrent protection mechanisms.
Technical specifications for BD series chambers.
Qualification requirements for personnel operating the chamber.
Important safety guidelines for installation and operation.
Description of the chamber's proper applications and limitations.
Instructions for safely moving and transporting the chamber.
Requirements for the installation site and environmental conditions.
Detailed instructions and data for connecting the chamber electrically.
Description of the controller buttons, symbols, and display.
How to set temperature and fan speed values.
Procedure for setting user and controller access passwords.
Description of the class 1 overtemperature protection device.
Details on the adjustable electronic safety controller and its classes.
How to set the limit temperature for the safety controller.
How to handle alarm messages and system responses.
Overview of available timer functions and their operation.
Detailed steps for setting the "Delayed Off" timer function.
Steps for setting the temperature-dependent delayed off timer.
Setting timer run-time, fan, and set-point for temperature-dependent timer.
Steps for setting the "Delayed On" timer function.
Setting timer run-time and fan speed for Delayed On timer.
How to program and view ramp function settings.
Viewing and modifying the ramp set-point.
Instructions on how to initiate data recording via USB.
Instructions on how to stop data recording via USB.
How to manually set the chamber's IP address.
Procedures and recommended agents for cleaning the chamber.
Methods for decontaminating the chamber after exposure to hazardous substances.
Overview of maintenance, service, and personnel requirements.
Recommended intervals and procedures for maintenance.
Common faults and their solutions for operating personnel.
Description of overcurrent protection mechanisms.
Technical specifications for BD series chambers.
General| Brand | Binder |
|---|---|
| Model | ED 115 |
| Category | Laboratory Equipment |
| Language | English |
