To Next PageTo Next PageWhy does my Binder Climate chamber take longer to heat up?
If you're experiencing deviations from the indicated heating-up times with your Binder Climate chamber, it might be because the chamber is fully loaded. Try loading the chamber with fewer items or allow for longer heating-up times.
How to fix high temperature and red alarm on Binder Climate chamber?
If the temperature inside your Binder Climate chamber is too high and the red alarm light is on, the safety device class 3.1 may have been triggered. Check the settings of the temperature set-point and of the safety device class 3.1.
Why is my Binder Climate chamber heating permanently?
If your Binder Climate chamber is heating permanently and not maintaining the set-point, the controller may be defective, in that case contact BINDER service. Alternatively, the controller might need calibration and adjustment.
What to do if Binder Climate chamber isn't working and the red alarm light is on?
If your Binder Climate chamber isn't working and the red alarm pilot lamp is lit, it could be that the safety device class 2 has turned off the chamber. Let the chamber cool down and then press the RESET button. Also, the safety device class 2 might be defective, in that case contact BINDER service.
What to do if Binder ED 115 chamber has no function?
First, check the connection to the power supply. If that's not the issue, the overtemperature protective device class 1 might have turned off the chamber. Disconnect the chamber from the power supply for at least 10 seconds and let it cool down. If the device responds again, further assistance is needed.
What to do if Binder Climate chamber set-point temperature is not reached?
If the set-point temperature isn't reached in your Binder Climate chamber, ensure the chamber door is completely closed. Also, inspect the door gasket and replace it if it’s defective. Calibrate and adjust the controller. Finally, check the power supply to ensure the voltage is correct (115V or 230V).
Why is my Binder Climate chamber not working?
Your Binder Climate chamber might not be working due to several reasons. First, check the connection to the power supply. Second, the chamber fuse might have responded, so check it and replace it if needed. If it responds again, contact BINDER service. Finally, the controller could be defective, in which case you should also contact BINDER service.
What does it mean if my Binder ED 115 chamber is without function, and the standby icon is displayed?
The chamber is likely in standby mode. Press down the standby button until the display lights up.
What to do if my Binder ED 115 chamber is heating permanently, and the set-point is not held?
The controller may not be adjusted correctly. Calibrate and adjust the controller.
What to do if my BD, BF Binder Laboratory Equipment displays alarm message “!TProt”?
The alarm message “!TProt” indicates that safety device class 3.1 has responded. Check the settings of the temperature set-point and of the safety device class 3.1.
Qualification requirements for personnel operating the chamber.
Important safety guidelines for installation and operation.
Description of the chamber's proper applications and limitations.
Instructions for safely moving and transporting the chamber.
Requirements for the installation site and environmental conditions.
Detailed instructions and data for connecting the chamber electrically.
Description of the controller buttons, symbols, and display.
How to set temperature and fan speed values.
Procedure for setting user and controller access passwords.
Description of the class 1 overtemperature protection device.
Details on the adjustable electronic safety controller and its classes.
How to set the limit temperature for the safety controller.
How to handle alarm messages and system responses.
Overview of available timer functions and their operation.
Detailed steps for setting the "Delayed Off" timer function.
Steps for setting the temperature-dependent delayed off timer.
Setting timer run-time, fan, and set-point for temperature-dependent timer.
Steps for setting the "Delayed On" timer function.
Setting timer run-time and fan speed for Delayed On timer.
How to program and view ramp function settings.
Viewing and modifying the ramp set-point.
Instructions on how to initiate data recording via USB.
Instructions on how to stop data recording via USB.
How to manually set the chamber's IP address.
Procedures and recommended agents for cleaning the chamber.
Methods for decontaminating the chamber after exposure to hazardous substances.
Overview of maintenance, service, and personnel requirements.
Recommended intervals and procedures for maintenance.
Common faults and their solutions for operating personnel.
Description of overcurrent protection mechanisms.
Technical specifications for BD series chambers.
General| Brand | Binder |
|---|---|
| Model | ED 115 |
| Category | Laboratory Equipment |
| Language | English |
