To Next PageTo Next PageWhat to do if the set-point temperature is not reached in my Binder Laboratory Equipment?
If the set-point temperature isn't reached after the specified time, there might be a few reasons. First, make sure the chamber door is completely closed. If it is, inspect the door gasket for any defects and replace it if necessary. Also, the controller might need adjustment; try calibrating it.
What causes my Binder FP 720 Laboratory Equipment chamber to heat permanently and not hold the set-point?
If your chamber is heating permanently and not holding the set-point, calibrate and adjust the controller. For other potential causes, contact Binder service.
Why are there deviations from the indicated heating-up times in my Binder FP 720 Laboratory Equipment?
Deviations from the indicated heating-up times can occur if the oven is fully loaded. Try charging the oven with less material or consider allowing longer heating-up times.
Why is my Binder FP 720 chamber permanently turned off?
If the chamber is permanently turned off, first check the connection to the power supply. Ensure the correct voltage (115V or 230V) is being supplied. Also, check the chamber fuse and replace it if needed. If the fuse responds again, contact Binder service.
What to do if the red indicator lamp is lit and my Binder FP 720 chamber is permanently turned off?
If the red indicator lamp of safety device class 2 is lit and the chamber is permanently turned off, let the oven cool down and then press the RESET button. Check the temperature set-point and the setting of the safety device, and select a suitable limit value if appropriate.
What to do if my Binder FP 720 Laboratory Equipment chamber doesn’t heat up, the LED is not lit, but the controller display is working?
If the chamber doesn’t heat up, the LED is not lit, and the controller display is working, contact Binder service.
What to do if my Binder FP 720 Laboratory Equipment chamber doesn’t heat up, but the LED is lit?
If the chamber doesn’t heat up but the LED is lit, contact Binder service.
Why is the program duration longer than programmed on my Binder FP 720?
If the program duration is longer than programmed, it may be due to inappropriate tolerances. For rapid transition phases, do NOT program tolerance limits to allow maximum heating speed.
How to fix ramp temperature transitions that are only realized as steps in my Binder FP 720 Laboratory Equipment?
If ramp temperature transitions are only realized as steps, set the set-point programming type to “Ramp” in the User level.
Why does my Binder FP 720 program stop one section too early?
If the program stops one section too early, the program line might be incomplete. Define the end value of the desired cycle by adding an additional section with a section time of at least one minute when programming.
Safety guidelines for chamber setup and daily use.
Details of the interface for operating the chamber.
Requirements for chamber placement and operational environment.
How to connect the chamber to the power supply.
Initial configuration of the RD3 program controller.
Choosing temperature transition methods: ramp or step.
How to program gradual temperature changes.
How to program sudden temperature changes.
Detailed steps for entering program values.
Procedure for removing program segments.
Defines target temperatures for different periods.
Step-by-step guide for program editor setup.
How the chamber behaves after power interruptions.
Explanation of error messages and buzzer functions.
Description and function of the class 2 safety device.
Description of the optional class 3.1 safety device.
Procedures for cleaning and disinfecting the chamber.
Detailed specifications for chamber models.
Safety guidelines for chamber setup and daily use.
Details of the interface for operating the chamber.
Requirements for chamber placement and operational environment.
How to connect the chamber to the power supply.
Initial configuration of the RD3 program controller.
Choosing temperature transition methods: ramp or step.
How to program gradual temperature changes.
How to program sudden temperature changes.
Detailed steps for entering program values.
Procedure for removing program segments.
Defines target temperatures for different periods.
Step-by-step guide for program editor setup.
How the chamber behaves after power interruptions.
Explanation of error messages and buzzer functions.
Description and function of the class 2 safety device.
Description of the optional class 3.1 safety device.
Procedures for cleaning and disinfecting the chamber.
Detailed specifications for chamber models.
General| Brand | Binder |
|---|---|
| Model | FP 720 |
| Category | Laboratory Equipment |
| Language | English |
