Binder KMF 115 - Page 11

To Next Page

To Previous Page

KMF (E5.2) 06/2014 page 11/99

Figure 1: Position of labels on the unit front KMF-UL

Figure 2: Position of labels on the unit rear

Keep safety labels complete and legible.

Replace safety labels that are no longer legible. Contact BINDER Service for these replacements.

Main Page

Default Chapter2
- EC - Declaration of Conformity2
- Product Registration4
- Table of Contents5
1 Safety8
- Legal Considerations8
- Structure of the Safety Instructions8
- Localization / Position of Safety Labels on the Unit10
- Type Plate12
- General Safety Instructions on Installing and Operating the Constant Climate Chamber13
- Intended Use15
- Resistance of the Humidity Sensor against Harmful Substances16
2 Unit Description17
- Unit Overview18
- Instrument Box18
- Lateral Control Panel, Right Side19
- Lateral Control Panel, Left Side (Option)20
- Unit Rear with Water Connections21
3 Completeness of Delivery, Transportation, Storage, and Installation22
- Unpacking, and Checking Equipment and Completeness of Delivery22
- Guidelines for Safe Lifting and Transportation23
- Storage24
- Location of Installation and Ambient Conditions24
4 Installation and Connections26
- Spacer for Wall Distance26
- Wastewater Connection26
- Freshwater Supply27
- Electrical Connection31
5 Start up32
- Function Overview of the MB1 Display Program Controller32
- Operating Modes33
- Performance after Power Failures33
- Turning on the Unit34
6 Mb1 Controller Settings35
- Selection of the MB1 Program Controller's Menu Language35
- Function Overview of the MB1 Program Controller Displays36
- Menu Settings in the "User-Settings" Menu37
- Menu Settings in the "User Level" Menu38
7 Graphic Representation of the Historical Measurement (Chart Recorder Function)39
- Setting the Storage Rate41
8 Manual Mode42
- Entering the Set Point Values42
- Performance after Power Failure in Manual Mode43
9 Program Operation44
- Menu-Based Program Entry44
- Entry of Temperature Values and Fan Speed45
- Entry of Humidity Values47
- Selecting between "Set-Point Ramp" and "Set-Point Step48
- Program Entry as "Set-Point Ramp" or as "Set-Point Step48
- Information on Programming Different Temperature or Humidity Transitions51
- Repetition of a Section or Several Sections Within a Program52
- Performance after Power Failure in Program Mode52
- Starting a Previously Entered Program53
- Deleting a Program53
- Template for Temperature Profile54
- Template for Humidity Profile55
- Program Table Template for Temperature and Fan Speed Rate56
- Program Table Template for Humidity57
10 Temperature Safety Devices58
- Over Temperature Protective Device (Class 1)58
- Safety Controller (Temperature Safety Device Class 3.1)58
  - Safety Controller Set-Point Types58
  - Checking and Setting Safety Controller Set-Point Type and Safety Controller Set-Point59
- Temperature Safety Device Class 3.3 (DIN 12880) (Option)60
  - Temperature Safety Device Class 3.161
  - Temperature Safety Device Class 3.262
11 Notification and Alarm Functions63
- Notification and Alarm System Overview (Auto Diagnosis System)63
- Resetting the Notification or Alarm Messages64
12 Humidity System65
- Function of the Humidifying and Dehumidifying System66
13 Defrosting at Refrigerating Operation68
14 Options69
- Communication Software APT-COM™ 3 Datacontrolsystem (Option)69
- Interface RS 422 (Option)69
- Data Logger Kits (Option)69
- Analog Outputs for Temperature and Humidity (Option)70
- Keyboard Locking (Option)70
- Additional Flexible Pt 100 Temperature Sensor (Option)71
- External Freshwater and Wastewater Cans (Option)71
- BINDER Pure Aqua Service (Option)75
15 Maintenance, Cleaning, and Service75
- Maintenance Intervals, Service75
- Cleaning and Decontamination76
  - Cleaning76
  - Decontamination78
- Sending the Unit Back to BINDER Gmbh79
16 Disposal79
- Disposal of the Transport Packing79
- Decommissioning80
- Disposal of the Unit in the Federal Republic of Germany80
- Disposal of the Unit in the Member States of the EC Except for the Federal Republic of Germany81
- Disposal of the Unit in Non-Member States of the EC82
17 Troubleshooting83
18 Technical Description86
- Factory Calibration and Adjustment86
- Over Current Protection86
- Definition of Usable Volume86
- KMF Technical Data87
- Equipment and Options KMF89
- Spare Parts and Accessories90
- Dimensions KMF 11591
- Dimensions KMF 24092
- Dimensions KMF 72093
19 Contamination Clearance Certificate94
- For Units Located Outside North America and Central America94
- For Units in North America and Central America97

Binder KMF 115 - Page 11

Table of Contents

Related product manuals