To Next PageTo Next Page
Need help?Do you have a question about the Biostar H61M U3 and is the answer not in the manual?
General| Form Factor | Micro ATX |
|---|---|
| Socket | LGA 1155 |
| Chipset | Intel H61 |
| Memory Type | DDR3 |
| Memory Slots | 2 |
| Max Memory | 16GB |
| Storage | 4 x SATA 3Gb/s |
| Audio | Realtek ALC662 6-Channel HD Audio |
| LAN | Realtek RTL8111E Gigabit LAN |
| Video Outputs | VGA, DVI-D, HDMI |
| Power Connector | 24-pin ATX, 4-pin ATX 12V |
| USB Ports | 8 x USB 2.0 (4 on back panel, 4 via headers), 2 x USB 3.0 (on back panel) |
Configures settings for PCI, PCI-X, and PCI Express devices.
Manages ACPI sleep states and wake-up event configurations.
Configures CPU features like Hyper-Threading and cores.
Sets SATA mode and enables/disables SATA controllers.
Configures USB legacy support and EHCI hand-off.
Configures parameters for the North Bridge chipset.
Configures settings for the South Bridge chipset.
Sets the number of seconds to wait for the setup activation key.
Selects the keyboard NumLock state at boot.
Enables or disables the Full Screen LOGO display.
Controls the Gate A20 line activation during boot.
Sets the Administrator Password for BIOS setup access.
Sets the User Password for power-on and setup access.
Sets the default entrance page when entering UEFI BIOS Setup.
Enables or disables a fixed CPU Ratio for performance.
Adjusts the CPU multiplier for performance tuning.
Sets the CPU Base Clock frequency.
Sets the maximum instantaneous CPU current.
Sets the sustained power limit for the CPU.
Enables or disables the second power limit feature.
Sets the short-duration power limit for the CPU.
Enables or disables Intel SpeedStep for power management.
Enables or disables Intel Turbo Mode for increased performance.
Enables or disables the CPU C1E Enhanced Halt State function.
Sets the Graphics Core Ratio limit.
Adjusts the DDR3 DRAM multiplier for memory performance.
Allows manual or automatic regulation of DRAM timings.
Selects the command rate for DDR3 memory.
Selects the CAS Latency timing for DDR3 memory.
Selects the Row Precharge Time for DDR3 memory.
Selects the RAS to CAS Delay timing for DDR3 memory.
Selects the Row Active Time for DDR3 memory.
Selects the Write Recovery Time for DDR3 memory.
Selects the Minimum Refresh Recovery Time for DDR3 memory.
Selects the Write to Read Delay for DDR3 memory.
Selects the Active to Active Delay for DDR3 memory.
Selects the Read to Precharge Delay for DDR3 memory.
Selects the Four Active Window Delay for DDR3 memory.
Sets the CPU Request Voltage.
Sets the CPU over voltage mode.
Sets the CPU Vcore Offset Voltage.
Sets the CPU Vcore Fixed Voltage.
Sets the mode of the Integrated Graphics Device core power supply.
Sets the IGD Vcore Offset Voltage.
Sets the IGD Vcore Fixed Voltage.
Sets the PWM Work Frequency.
Enables or disables PWM I-OUT Override.
Enables or disables PWM Thermal report Override.
Sets the VCore LoadLine.
Sets the DRAM Voltage.
Sets the CPU PLL power supply.
Sets the PCH Voltage.
Displays SPD information of DDR3 memory modules.
Abandons all changes and exits the setup utility.
Resets the system after saving the current changes.
Reloads the BIOS to factory optimized settings.
Allows selection of a boot device for a single boot.
Executes the Windows Boot Manager.
Executes the UEFI BIOS built-in EFI Shell.
