Bizerba SC II 400 User Manual (English)

Questions and Answers:

P
Patricia West MDAug 26, 2025
Why is the weight value display not at zero on Bizerba SC II 400 Scales?
- J
  Jessica GilmoreAug 26, 2025
  If your Bizerba Scales display a weight value that is not at zero or appears modified, it could be due to a few reasons: the load plate may not be correctly positioned, there might be objects on the load plate, or there could be soiling on or beneath the load plate. To fix this: * Clean the load plate. * Position it correctly. * Remove any objects. Also, ensure the scale is leveled properly.
S
saramercerAug 27, 2025
What does 'Not in tare range' mean on Bizerba SC II 400?
- H
  Heather HayesAug 27, 2025
  If your Bizerba Scales show 'Not in tare range' during sales, it means the scales were in an underload range when attempting to tare. To fix this, unload the scales, reset them, and then retry the taring process.
J
James WarrenAug 27, 2025
What to do if Bizerba SC II 400 say 'Please apply article'?
- T
  Timothy HernandezAug 27, 2025
  If your Bizerba Scales display 'Please apply article', it means self-service mode is activated. Place the article on the scale.
C
Cody JamesAug 27, 2025
What does 'Evaluation active on another scale' mean on Bizerba Scales?
- Q
  qsanchezAug 27, 2025
  If your Bizerba Scales display 'Evaluation active on another scale' when printing a report, it means the same report has been started on another set of scales. Wait until the report has finished printing out, then restart the report.
C
Catherine MaddenAug 27, 2025
What does 'Evaluation active on another station' mean on Bizerba Scales?
- R
  Regina DurhamAug 27, 2025
  If your Bizerba Scales display 'Evaluation active on another station', it means the same report is being started on several devices. Wait until the report is completed on the other devices.
V
Veronica JohnsonAug 28, 2025
What to do if Bizerba SC II 400 Scales say 'Please press key'?
- M
  Mary GordonAug 28, 2025
  If your Bizerba Scales display 'Please press key' when self-service mode is activated, press the button.
S
Sean RasmussenAug 28, 2025
What to do if Bizerba SC II 400 Scales show 'Operator is not a cashier!'?
- T
  Tiffany LambertAug 28, 2025
  If your Bizerba Scales show 'Operator is not a cashier!', and the SC II is operated with the setting 'Configuration' / 'Cash desk' / 'Amount tend./change op.' set to YES, check the settings for the applicable operator in the 'Data maintenance' / 'Operator data' menu.
L
Laura ScottAug 28, 2025
What does 'Code structure not defined' mean on Bizerba SC II 400?
- J
  John BrownAug 29, 2025
  If your Bizerba Scales display 'Code structure not defined', it means you are scanning an article with a code digit (e.g. 21....... ) that refers to a code structure number not defined in the 'Data maintenance' / 'Code structures' menu. Correct the code digit or define a code structure to correspond to the code digit in the 'Data maintenance' / 'Code structures' menu.
T
Tiffany AdamsAug 29, 2025
How to fix 'The text is XXX characters too long ! The text was not saved !' error on Bizerba SC II 400?
- C
  Crystal JacksonAug 29, 2025
  If your Bizerba Scales display 'The text is XXX characters too long ! The text was not saved !' in the PLU maintenance when entering PLU text, shorten the PLU text and save it. The maximum value is 500 characters / 20 lines.
J
Jennifer MartinezAug 25, 2025
What does 'Attention!! Scales switched off, please switch on!' mean on Bizerba SC II 400?
- J
  Joseph RussoAug 25, 2025
  If your Bizerba Scales display 'Attention!! Scales switched off, please switch on!', it indicates that the scales are not activated. Switch on all scales and ensure the connection cable is properly inserted and checked.

Bizerba SC II 400 Specifications

General

Max. Load	6 kg / 15 kg
Readability	1 g / 2 g
Display	LCD
Power supply	230 V AC
Weighing capacity	6 kg / 15 kg
Material	Stainless steel
Interfaces	RS232, Ethernet

Summary

About these instructions

Warnings

Explanation of danger levels and their meaning in warnings.

About the device

Verification information

Information related to scale verification and legal requirements.

Metrological notes for EU countries

Details on metrology marks, conformity assessment, and trade use in EU countries.

Information on verification

Explanation of verification processes and validity periods for scales.

Standards and directives

Lists standards and directives related to measuring technology.

Electromagnetic compatibility

Lists standards related to electromagnetic compatibility (EMC).

Electrical safety

Lists standards related to electrical safety.

Operating conditions

Important conditions to note before and during device operation.

Power supply

Details on power supply installation and international specifications.

Wireless LAN device network

Instructions and rules for wireless LAN device network usage.

Safety instructions

System-related sources of hazards

Identifies hazards related to the scale system and safety precautions.

Requirements for operating personnel

Specifies qualifications and responsibilities for personnel operating the equipment.

Installation

Start-up

Information on putting the device into operation and initial setup.

Switching device on

Instructions on how to switch the device on and its requirements.

Installation and assembly

Instructions for installing and assembling the scale device.

Installation of power supply provided by customer

Customer's responsibility for installing the power supply according to standards.

Check before connecting to mains!

Crucial checks before connecting the device to the mains power.

Cable connections

Instructions and cautions for making cable connections to the device.

Device and operating controls

Key functions

Explanation of basic and extended keyboard functions and configuration.

Operation

Switching device on

Instructions on how to power on the scale device.

Switch off device

Procedure for safely switching off the scale device.

Correction options

SC II 100 K/B operation with weight value

PLU call-up

Methods for accessing Product Look-Up (PLU) data for articles.

Operating procedure after PLU call-up

Steps following a PLU call-up.

Registering manual weight input

Multiplication of PLU piece-price article with predefined quantity

Multiplication of PLU price per piece with a partial number of pieces

Operation procedure without PLU call-up

Cancellation

Procedures for canceling articles before completing a transaction.

Total

Tare

Procedures related to tare balancing for various scenarios.

Tare balancing with known tare

Procedures for tare balancing with known tare values.

Assisted sale with labels

Article with fixed volume and fixed price

PLU with data of origin

Sale with abbreviated traceability number from configuration

Self-service mode

Cash register functions

Using cash register functions, including pay-in/pay-out.

Sale of articles with different price types

Handling articles with various price types like graduated or fixed prices.

n*quantity grad.

n*amount grad.

Percent graduation

Amount graduation

Mix. special price

Obligatory input for piece price for piece-price articles

Obligatory input always

Obligatory input limited

Sale with weight-fixed-price article

Handling articles with fixed weight and price.

PLU type: "By-count weighed"

PLU type: "Manual fixed weight"

PLU type:"By-count fixed weight"

PLU type: "By count"

Using "By count" PLUs for piece articles with saved piece numbers.

Mandatory input for By-count

Troubleshooting

Fault description

Table listing common faults, their causes, and elimination steps.

Messages

List of text messages, their causes, and remedies.

Maintenance

Cleaning

General instructions and precautions for cleaning the device.

Cleaning the printer

Maintenance

Related product manuals

Bizerba SC II 400 User Manual

Table of Contents

Questions and Answers:

Bizerba SC II 400 Specifications

Summary

About these instructions

Warnings

About the device

Verification information

Metrological notes for EU countries

Information on verification

Standards and directives

Electromagnetic compatibility

Electrical safety

Operating conditions

Power supply

Wireless LAN device network

Safety instructions

System-related sources of hazards

Requirements for operating personnel

Installation

Start-up

Switching device on

Installation and assembly

Installation of power supply provided by customer

Check before connecting to mains!

Cable connections

Device and operating controls

Key functions

Operation

Switching device on

Switch off device

Correction options

SC II 100 K/B operation with weight value

PLU call-up

Operating procedure after PLU call-up

Registering manual weight input

Multiplication of PLU piece-price article with predefined quantity

Multiplication of PLU price per piece with a partial number of pieces

Operation procedure without PLU call-up

Cancellation

Total

Tare

Tare balancing with known tare

Assisted sale with labels

Article with fixed volume and fixed price

PLU with data of origin

Sale with abbreviated traceability number from configuration

Self-service mode

Cash register functions

Sale of articles with different price types

n*quantity grad.

n*amount grad.

Percent graduation

Amount graduation

Mix. special price

Obligatory input for piece price for piece-price articles

Obligatory input always

Obligatory input limited

Sale with weight-fixed-price article

PLU type: "By-count weighed"

PLU type: "Manual fixed weight"

PLU type:"By-count fixed weight"

PLU type: "By count"

Mandatory input for By-count

Troubleshooting

Fault description

Messages

Maintenance

Cleaning

Cleaning the printer

Maintenance

Related product manuals