Bluewater CLEONE - User Manual

Other manuals for Bluewater CLEONE

Owner's Manual156 pages

Questions and Answers

R
Robert LunaAug 15, 2025
What to do if no water comes from the clean water faucet and the system operation indicator is off in Bluewater CLEONE Water Filtration Systems?
- D
  David MaynardAug 15, 2025
  If no water is coming from the clean water faucet and the system operation indicator is off, there might be several reasons. First, check if the Cleone is properly connected to an electrical outlet and the power adapter, ensuring the 24V DC cable is connected to the electrical power socket. Next, verify that the Cleone is started by moving the power switch to position 1. Finally, if an internal leak has been sensed, the Cleone might have automatically stopped, in which case you should contact your Bluewater dealer to repair the leak and reset the system.
R
Robert AdamsAug 17, 2025
Why is the flow rate from the clean water faucet low in my Bluewater CLEONE Water Filtration Systems?
- M
  Maria FitzgeraldAug 18, 2025
  If the flow rate from the clean water faucet is low, this could be due to the clean water tank being empty because of high water consumption. Consider upgrading to a larger tank or a high-capacity membrane. Alternatively, the air pressure in the clean water tank might be low, in which case you should contact your Bluewater dealer to restore the correct air pressure.
A
adkinsbreannaAug 21, 2025
What to do if no water comes from the clean water faucet, but the system operation indicator is on, in Bluewater CLEONE Water Filtration Systems?
- A
  Alejandro LewisAug 21, 2025
  If no water is coming from the clean water faucet but the system operation indicator is on, it could be because the Cleone has been installed for the first time and the system is not filled with water. Wait for the system to fill with water and flush Cleone. Another reason might be that the water tubes are not connected properly, so ensure the connections are correctly made. It may also be the result of prefilters being clogged due to lack of regular maintenance, in this case you should contact your Bluewater dealer to do maintenance on Cleone.
D
Dr. Elaine PenaAug 25, 2025
What does it mean if the system operation indicator flashes slowly (2 sec ON, 2 sec OFF) on Bluewater CLEONE Water Filtration Systems?
- V
  Victoria DanielsAug 26, 2025
  If the system operation indicator flashes slowly (2 sec ON, 2 sec OFF), it means the filters must be replaced. Replace the filters and reset the filter indicator.
L
Laura LopezAug 28, 2025
What does it mean if the system operation indicator flashes quickly (0.5 sec ON, 0.5 sec OFF) and water comes from the clean water faucet from Bluewater CLEONE?
- J
  Joshua ShermanAug 28, 2025
  If the system operation indicator flashes quickly (0.5 sec ON, 0.5 sec OFF) and water comes from the clean water faucet, it means the water quality has decreased. While it is safe to use the cleaned water, contact your Bluewater dealer for more information.
D
Daniel CurryAug 31, 2025
Why does clean water contain particles in my Bluewater CLEONE Water Filtration Systems?
- J
  johnjacksonAug 31, 2025
  If clean water contains particles, it may be because the water purifier has not been flushed and conditioned after postfilter change (Activated carbon postfilter, integrated mineral filter). Flush and condition Cleone.
B
Brianna BeckSep 3, 2025
What to do if no water comes from the clean water faucet and the system operation indicator flashes with high intensity (0.1 sec ON, 0.1 sec OFF) on Bluewater Water Filtration Systems?
- D
  Debra WilliamsSep 4, 2025
  If no water comes from the clean water faucet and the system operation indicator flashes with high intensity (0.1 sec ON, 0.1 sec OFF), it means the feed water pressure is too low and the pump protection system has stopped the feed water supply. Remove the cause of the low feed water pressure and turn the power off and on to start Cleone again.
A
Aaron PhelpsSep 7, 2025
What to do if no water comes from the clean water faucet and the system operation indicator flashes quickly (0.5 sec ON, 0.5 sec OFF) on Bluewater CLEONE?
- A
  Allison HensonSep 7, 2025
  If no water comes from the clean water faucet and the system operation indicator flashes quickly (0.5 sec ON, 0.5 sec OFF), it means Cleone has stopped because the water quality is low. Contact your Bluewater dealer for service.
J
James KellySep 12, 2025
Why is there too much continuous noise during water purification with Bluewater CLEONE Water Filtration Systems?
- K
  kellymoralesSep 12, 2025
  If there is too much continuous noise during water purification, it is necessary to do maintenance on the booster pump. Contact your Bluewater dealer.

Summary

INTRODUCTION

Safety instructions

Emphasizes reading safety information to prevent injury or equipment damage.

Low pressure protection

Low pressure restart function

Illustrates the automatic restart process when low pressure conditions are met.

Manual restart after low pressure cause has been removed

Shows the procedure for manually restarting the system after a low pressure issue.

Leak protection system

Illustrates the components and steps involved in the leak protection system.

INSTALLATION

Install clean water faucet

Install feed water connection

Provides detailed steps for connecting the feed water supply to the purifier.

Install drain water connection

Explains the procedure for connecting the drain water outlet.

Connect tubing

Install power adapter

Details the installation of the power adapter, including safety precautions and US specific requirements.

After installation

Flush Cleone

Outlines the procedure for flushing the system after installation or maintenance.

Condition Cleone

Explains the conditioning process, warning against using the water due to preservative solution.

Do a check for leaks

Instructs on how to check for leaks after installation, emphasizing tight tubing connections.

Repair leaks

Provides a step-by-step guide on how to repair any detected leaks.

Each 6 months

Replace prefilters

Details the process for replacing the coarse sediment, fine sediment, and activated carbon prefilters.

Replace integrated mineral filter

Do a feed water pressure check

Feed water pressure check

Each year

Replace activated carbon postfilter

Replace UV lamp

Each 3-5 years

Replace reverse osmosis membrane

TROUBLESHOOTING

Troubleshooting

Provides a table of common issues, their causes, and solutions for the water purifier.

Bluewater CLEONE Specifications

General

Filtration Technology	Reverse Osmosis
Storage Tank Capacity	3.2 gallons
Warranty	1 year limited
Filter Stages	5
Operating Pressure	40-80 psi
Operating Temperature	40-100°F
Technology	Reverse Osmosis