To Next PageTo Next PageWhy does my Bosch 4405 motor not start?
If the motor of your Bosch Saw doesn't start, ensure the unit is plugged in and try a different outlet. Also, check the 15-Amp time delay fuse or circuit breaker.
What to do if my Bosch Saw blade binds, jams, burns wood or makes rough cuts?
If your Bosch Saw blade binds, jams, burns wood, or results in rough cuts, replace or sharpen the blade. You might also need to replace the blade with a 10” diameter blade designed for the material you are cutting.
What to do if my Bosch 4405 Saw tool vibrates or shakes?
If your Bosch Saw vibrates or shakes, check the proper installation of the blade onto the saw. Replace the blade or tighten the arbor screw.
How to fix Bosch Saw brake that does not stop blade in about 5 seconds?
If the brake on your Bosch Saw does not stop the blade within about 5 seconds, inspect, clean, or replace the brushes. Use a sharp or recommended blade, let the saw cool down, and tighten the blade bolt.
Why Bosch Saw head assembly does not slide freely when attempting a slide cut?
If the head assembly of your Bosch Saw does not slide freely when attempting a slide cut, loosen the slide rail lock knob. The glide pods might also need adjustment.
Why Bosch Saw head assembly slides forward and back when making a chop cut?
If the head assembly of your Bosch Saw slides forward and back when making a chop cut, push the head assembly completely against the stop and tighten the slide rail lock knob.
Why I cannot move miter adjustment on my Bosch 4405?
If you cannot move the miter adjustment on your Bosch Saw, loosen the lock knob or move it out of the detent. Also, vacuum or blow out any dust, and extend the sliding fence.
Why Bosch Saw head assembly will not fully rise or blade guard will not fully close?
If the head assembly of your Bosch Saw will not fully rise or the blade guard will not fully close, clean the head assembly. Lubricate the head pivot pin with light oil spray or silicone lube.
How to fix loose slide fence on Bosch 4405 Saw?
To fix a loose slide fence on your Bosch Saw, tighten the fence lever and adjust the lower tension.
Why Bosch Saw blade hits table?
If the blade of your Bosch Saw hits the table, check the proper installation of the blade onto the saw, as misalignment may be the cause.
General| Blade Diameter | 10 inches |
|---|---|
| Power Source | Corded Electric |
| Motor Amperage | 15 Amps |
| Spindle Lock | Yes |
| Depth of Cut at 45° | 2-1/4 inches |
| Maximum Cutting Depth | 70 mm |
| Arbor Size | 5/8 inches |
| No Load Speed | 5000 rpm |
| Depth of Cut at 90° | 70 mm |
Essential safety guidelines for operating bench top tools, covering work area and personal safety.
Guidelines for safe use of electrical components and power supply to prevent shock hazards.
Proper techniques for using and maintaining the tool safely, including blade care and guards.
Critical safety instructions tailored for the operation of miter saws to prevent accidents.
Understanding double insulation and proper selection and use of extension cords for safety.
Information on required electrical circuits and the function of the saw's electric brake system.
Locating and understanding the function of primary parts like switches, locks, guards, and fences.
Details on less common but important components such as depth stops, clamp positions, and adjusters.
Lists necessary tools for assembly and guides on unpacking and verifying all parts are present.
Step-by-step instructions for attaching specific parts like the miter lock knob and dust collection system.
Detailed guide on how to safely install and remove the saw blade, including hardware.
Procedures to ensure the blade is perfectly square to the table at 0° and 90°.
Steps to accurately set and calibrate the 45° bevel angle for precise cuts.
Procedure to accurately set and calibrate the 33.9° bevel angle for specific cuts.
Ensuring the blade is square to the fence and calibrating the miter scale indicator.
Instructions for securely mounting the miter saw to a workbench or stand.
Adjusting the stability bar and using clamps for portable mounting to ensure stability.
Guidance on maintaining correct body posture and safe hand placement during operation.
Techniques for properly supporting and clamping workpieces for stable and safe cutting.
Instructions for utilizing auxiliary fences, switch activation, and detent overrides.
Procedures for extending the base and adjusting the sliding fence for various cuts.
Detailed steps for performing basic chop cuts and slide cuts on the miter saw.
Instructions for executing miter and bevel cuts accurately and safely.
Guidance on performing compound cuts and cutting grooves (dadoes).
Specific techniques for cutting base molding and crown molding accurately.
Methods for safely cutting bowed or irregularly shaped workpieces.
Essential procedures for servicing, cleaning, and maintaining the saw and its blades.
Guidance on proper lubrication practices and information regarding the tool's bearings.
Diagnosing and resolving issues related to the saw's electrical components and power.
Solutions for common problems encountered during saw operation, including alignment and movement.
Instructions for adjusting the slide action and bevel lock lever for optimal performance.
Overview of various saw blades and optional accessories designed to enhance tool functionality.
