English | 39
Bosch Power Tools 1 609 929 X57 | (12/5/11)
– Tighten the adjustment screw 81 until the parallel guide
can be firmly affixed on the saw table again.
Storage and Transport
Storing Product Features (see figures R1–R6)
For storage purposes, certain product features can be se-
curely fastened to the power tool.
– Loosen auxiliary parallel guide 49 from parallel guide 8.
– Attach all loose tool parts to their storage locations on the
housing. (see Table)
Carrying the Power Tool
Before transporting the power tool, the following steps must
be carried out:
– Bring the machine into the transport position. (see “Trans-
port Position”, page 35)
– Remove all accessories that cannot be mounted firmly to
the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.
– Slide the table width enlargement 11 completely in and
press tensioning lever 18 downward to lock it.
– Slide the table extension 10 completely in and firmly tight-
en the locking screws 38 on the guide rods 24.
– Wind the mains cable around the cable holder 42.
– For lifting or transport, use the carrying handles 4.
f When transporting the power tool, only use the trans-
port fixtures. Never carry the power tool by the protec-
tive devices, the table extension 10 or the table width
enlargement 11.
f The power tool should always be carried by two per-
sons in order to avoid back injuries.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine itself, pull the mains
plug.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Cleaning
– For safe and proper working, always keep the power tool
and its ventilation slots clean.
– Remove dust and chips after each working procedure by
blowing out with compressed air or with a brush.
Power Tool Lubrication
Lubricants:
SAE 10/SAE 20 engine oil
– If required, open the bottom plate and apply oil to the lubri-
cation points of the power tool at the indicated locations.
(seefiguresS1–S2)
An authorized Bosch after-sales service agent will carry out
this work quickly and reliably.
Observe all applicable environmental regulations when
disposing of old grease and solvents.
Measures for Noise Reduction
Measures on behalf of the manufacturer:
–Soft starting
– Delivery of the machine with a saw blade developed partic-
ularly for noise reduction
Measures on behalf of the user:
– Low-vibration assembly on a firm working surface
– Use of saw blades with noise-reducing functions
– Regular cleaning of saw blade and power tool
Accessories
Dust bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 610 015 511
Extraction adapter . . . . . . . . . . . . . . . . . . . . .2 610 015 509
Y-adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 610 015 513
Angle stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 610 015 508
Push stick . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 610 015 022
Saw stand GTA 60 W . . . . . . . . . . . . . . . . . . .0 601 B12 000
Saw stand GTA 6000 . . . . . . . . . . . . . . . . . . .0 601 B24 100
Figure Product Feature Storage Location
R1
Blade guard 5.x Insert into the recess of fixture
22 and tighten with clamping
lever 46.1 or clamping screw
46.2
R2
“Auxiliary parallel
guide” fastening kit
39
Clip into the holders 75
R2
Extraction adapter
41
Insert into retaining clamp 76
R3
Unused saw blades Insert into saw blade storage
77 and lock the cover 14 over
it with fastening nut 12
R3
Ring spanner 15 Insert into saw blade storage
77 and lock the cover 14 over
it with fastening nut 12
R3
Push stick 13 Lock in place with fastening
nut 12
R4
Allen key 37 Insert into holders 78
R4
Parallel guide 8 Insert into the storage com-
partment for the parallel guide
36
R5
Angle stop 3 Insert into retaining clamp 23
R6
Auxiliary parallel
guide 49
Insert into the storage com-
partment for the auxiliary par-
allel guide and lock in place
with the retaining bracket 79
OBJ_BUCH-1375-001.book Page 39 Thursday, May 12, 2011 2:22 PM
To Next Page
Loading...
