Why does my Bosch Sensixx DS38 make a pumping sound?
Your Bosch Iron may make a pumping sound because water is being pumped into the steam tank, or the water tank is not fitted onto the housing correctly. Fit the water tank back onto the housing correctly. If the sound will not stop, do not use the steam generator and contact an authorised technical service centre.
Why is my Bosch Sensixx DS38 not producing steam?
Your Bosch Iron may not be producing steam because the boiler is not switched on, or the water tank is empty. Set the power button to the “I” position and/or fill the water tank. Another possible reason is that the water tank is not fitted onto the housing correctly. To fix this, fit the water tank back onto the housing correctly.
Why does my Bosch Sensixx DS38 Iron begin to smoke when switched on?
If your Bosch Iron begins to smoke when switched on for the first time, this is because certain components on the appliance have been lightly greased at the factory and may produce a little smoke when initially heated. If it occurs during subsequent use, the soleplate may be soiled. Clean the soleplate according to the cleaning instructions in this manual.
What to do if my Bosch steam generator does not come on?
If your Bosch steam generator does not come on, first check the mains cable, the plug and the socket to ensure there isn't a connection problem. Also, make sure the power button is switched on by setting it to the “I” position.
What to do if my Bosch Ironed garment turns dark and/or sticks to the soleplate?
If your ironed garment turns dark or sticks to the soleplate of your Bosch Iron, it means that the selected temperature is too high and has damaged the garment. Select a suitable temperature for the material being ironed and clean the soleplate with a damp cloth.
Why do water spots appear on the garment during use of the “PulseSteam” function of my Bosch Sensixx DS38?
Water spots are caused by steam condensation in the hose when cooling down after use. Water drops stop coming out of the soleplate after using the “PulseSteam” function for some time.
Why do water spots appear on the garment during ironing with my Bosch Sensixx DS38 Iron?
Water spots appearing on the garment during ironing with your Bosch Iron may be caused by steam condensed on the ironing board. Wipe the textile cover of the ironing board, and iron any water drops to dry them.
What causes loss of pressure during ironing with my Bosch Sensixx DS38?
Loss of pressure during ironing with your Bosch Iron is caused by the steam release button being activated for too long or pressed too frequently. Use the steam release button at intervals to improve ironing results, allowing the textiles to be steamed, dried, and ironed properly.
Why is my Bosch Iron leaking water from the boiler?
If your Bosch Iron is leaking water from the boiler, the scale collector located at the bottom of the appliance may be loose. Tighten up the scale collector to resolve this issue.
What to do if dirt comes out through the soleplate of my Bosch Iron?
If dirt is coming out through the soleplate of your Bosch Iron, it could be due to a build-up of scale or minerals in the boiler and iron. Perform a cleaning cycle. It may also be because chemical products or additives have been used. Never add products to the water. Use tap water mixed 50% with distilled or demineralised water. To prolong the optimum steam function, mix tap water with distilled water 1:1. If the tap water in your area is very hard, mix tap water with distilled water 1:2. Clean the soleplate with a damp cloth.
General| Power | 2400 W |
|---|---|
| Steam output | 40 g/min |
| Cord length | 2.5 m |
| Vertical Steam | Yes |
| Anti-Calc System | Yes |
| Drip Stop System | Yes |
| Auto shut-off | Yes |
| Self-cleaning | Yes |
| Anti-drip system | Yes |
| Type | Steam Iron |
| Soleplate | Ceramic |
Detailed identification and explanation of all appliance parts and features.
Initial setup steps required before operating the steam iron.
Automatically sets optimal temperature and steam for all ironable fabrics.
Minimizes shiny marks on dark or delicate garments.
Initiates the appliance's internal descaling process.
Delivers powerful, concentrated steam shots for stubborn creases.
Provides a brief, additional steam release after the main trigger.
Removes creases from hanging garments or curtains.
Activates eco mode to reduce energy and water consumption.
Automatically powers down the appliance for enhanced safety.
Protects delicate fabrics from heat damage and prevents shine.
Safely cleaning the appliance body, handle, and soleplate.
Proper methods for storing the steam ironing system when not in use.
Recommendations for minimizing energy consumption during ironing.
To Next Page