To Next Page
C
Carla LeeAug 20, 2025
How to turn on Bose Computer Hardware?
- JJohn VasquezAug 20, 2025
To turn on your Bose Computer Hardware, ensure the power cord is plugged in and then turn the power switch to the 'on' position.
How to turn on Bose Computer Hardware?
To turn on your Bose Computer Hardware, ensure the power cord is plugged in and then turn the power switch to the 'on' position.
What to do if my Bose Computer Hardware has power but no sound?
First, make sure there's an input signal coming from the source. Then, check that there's an output signal. If there is an input signal (indicator green) but no output signal (indicators off), use ControlSpaceTM Designer software to connect to the ESP-88 and verify the settings.
Why is the sound distorted on my Bose Computer Hardware?
If the source output levels are too high, reduce the source output level, or use the Designer software to reduce the input gain. If the input indicators are green, use the Designer software to reduce the output gain or any intermediary gain in the signal path. Also, verify that the loudspeakers are not being overdriven or damaged.
How to increase the sound on my Bose Computer Hardware?
If the source output is low, increase the source output or use the Designer software to increase the input gain. Verify that the audio output signal indicator is green and that there is enough gain on the amplifier.
What to do if the Ethernet LED is on, but can't communicate with the ESP-88 on my Bose Computer Hardware?
Verify that the LAN settings on the Ethernet device you are using on the PC are set correctly. Also, make sure that there isn't another LAN connection enabled or another ESP connected with the same address.
Why is the Ethernet LED off on my Bose Computer Hardware?
Verify that the ESP LAN port is connected to a PC with a crossover cable. Also, ensure that the Ethernet LAN connection on the PC is enabled, and check the device's Link LED. Finally, verify that the ESP and PC are connected with straight-through cables to the hub or switch.
How to fix unnatural sound on Bose Computer Hardware?
Verify that the correct EQ and/or crossover is used in the signal path.
What to do if the Status LED is off on my Bose Computer Hardware?
Use ControlSpace Designer software to load a netlist/configuration.
What to do if the Ethernet LED is on but I cannot communicate with the Bose ESP-88 Recording Equipment?
If the Ethernet LED is lit but you can't communicate with the Bose ESP-88 Recording Equipment, check the LAN settings on your PC's Ethernet device. Ensure that Internet Protocol (TCP/IP) is installed, the IP address is set to 192.168.0.1, and the subnet mask is set to 255.255.255.0. Also, make sure there aren't any other enabled LAN connections or ESP units connected with the same address. If unsure, disconnect one unit, scan for the remaining one, and change its address, then repeat with the second unit.
Why is there no sound from my Bose Recording Equipment even though the power is on?
If your Bose Recording Equipment has power but no sound, first confirm that there's an input signal from the source, indicated by a green (or yellow) audio input indicator. Next, check for an output signal, which should also be indicated by a green (or yellow) audio output signal indicator. If there's an input signal but no output, the ESP-88 might be muted, output levels may be down, or the unit is un-programmed. Use ControlSpace Designer software to connect to the ESP-88 and verify that signals are passing from inputs to outputs.
General| Signal Processor Type | DSP |
|---|---|
| I/O Channels | 8x8 |
| Analog Inputs | 8 |
| Analog Outputs | 8 |
| Network Control | Yes |
| Power Supply | 100-240 VAC, 50/60 Hz |
| Audio Inputs | 8 analog |
| Audio Outputs | 8 analog |
| Connectivity | Ethernet, RS-232 |
| Control | Serial, Ethernet |
| Frequency Response | 20Hz - 20kHz |
| Signal-to-Noise Ratio | >100dB |
| Weight | 8.0 lb (3.6 kg) |
