Bose ControlSpace ESP-88

Questions and Answers

M
michellejacksonAug 20, 2025
How to turn on Bose Computer Hardware?
- L
  Lindsay WrightAug 20, 2025
  To turn on your Bose Computer Hardware, ensure the power cord is plugged in and then turn the power switch to the 'on' position.
K
katherinestanleyAug 22, 2025
What to do if my Bose Computer Hardware has power but no sound?
- M
  Monica Mcfarland DVMAug 22, 2025
  First, make sure there's an input signal coming from the source. Then, check that there's an output signal. If there is an input signal (indicator green) but no output signal (indicators off), use ControlSpaceTM Designer software to connect to the ESP-88 and verify the settings.
S
Shawn LiuAug 25, 2025
Why is the sound distorted on my Bose Computer Hardware?
- S
  Sara TuckerAug 25, 2025
  If the source output levels are too high, reduce the source output level, or use the Designer software to reduce the input gain. If the input indicators are green, use the Designer software to reduce the output gain or any intermediary gain in the signal path. Also, verify that the loudspeakers are not being overdriven or damaged.
B
Barbara PowersAug 26, 2025
How to increase the sound on my Bose Computer Hardware?
- A
  anthonychavezAug 26, 2025
  If the source output is low, increase the source output or use the Designer software to increase the input gain. Verify that the audio output signal indicator is green and that there is enough gain on the amplifier.
N
nicholas88Aug 27, 2025
What to do if the Ethernet LED is on, but can't communicate with the ESP-88 on my Bose Computer Hardware?
- P
  Patrick PattersonAug 28, 2025
  Verify that the LAN settings on the Ethernet device you are using on the PC are set correctly. Also, make sure that there isn't another LAN connection enabled or another ESP connected with the same address.
P
pgarzaAug 29, 2025
Why is the Ethernet LED off on my Bose Computer Hardware?
- E
  Edward GilbertAug 29, 2025
  Verify that the ESP LAN port is connected to a PC with a crossover cable. Also, ensure that the Ethernet LAN connection on the PC is enabled, and check the device's Link LED. Finally, verify that the ESP and PC are connected with straight-through cables to the hub or switch.
B
Brandi GonzalezAug 31, 2025
How to fix unnatural sound on Bose Computer Hardware?
- C
  Cody RoblesAug 31, 2025
  Verify that the correct EQ and/or crossover is used in the signal path.
J
Jason OneillSep 2, 2025
What to do if the Status LED is off on my Bose Computer Hardware?
- A
  Anne PenaSep 2, 2025
  Use ControlSpace Designer software to load a netlist/configuration.
K
Karen AdamsSep 4, 2025
What to do if the Ethernet LED is on but I cannot communicate with the Bose ESP-88 Recording Equipment?
- W
  william98Sep 4, 2025
  If the Ethernet LED is lit but you can't communicate with the Bose ESP-88 Recording Equipment, check the LAN settings on your PC's Ethernet device. Ensure that Internet Protocol (TCP/IP) is installed, the IP address is set to 192.168.0.1, and the subnet mask is set to 255.255.255.0. Also, make sure there aren't any other enabled LAN connections or ESP units connected with the same address. If unsure, disconnect one unit, scan for the remaining one, and change its address, then repeat with the second unit.
R
Richard BowmanSep 6, 2025
Why is there no sound from my Bose Recording Equipment even though the power is on?
- J
  John AdkinsSep 6, 2025
  If your Bose Recording Equipment has power but no sound, first confirm that there's an input signal from the source, indicated by a green (or yellow) audio input indicator. Next, check for an output signal, which should also be indicated by a green (or yellow) audio output signal indicator. If there's an input signal but no output, the ESP-88 might be muted, output levels may be down, or the unit is un-programmed. Use ControlSpace Designer software to connect to the ESP-88 and verify that signals are passing from inputs to outputs.