Bostitch D62ADC User Manual

-10-
TROUBLE SHOOTING
PROBLEM CAUSE CORRECTION
Trigger valve housing leaks air O-ring cut or cracked . . . . . . . . . . . . . .Replace O-ring
Trigger valve stem leaks air O-ring/seals cut or cracked . . . . . . . . .Replace trigger valve assembly
Frame/Piston rod leaks air O-ring . . . . . . . . . . . . . . . . . . . . . . . . . .Replace O-ring
F
rame/cap leaks air Damaged O-ring . . . . . . . . . . . . . . . . . .Replace O-ring
L
oose cap screws . . . . . . . . . . . . . . . .Tighten and recheck
F
ailure to cycle Air supply restriction . . . . . . . . . . . . . . .Check air supply equipment
Tool dry, lack of lubrication . . . . . . . . . .Use BOSTITCH Air Tool Lubricant
Broken piston . . . . . . . . . . . . . . . . . . . .Replace piston
Lack of power; slow to cycle Tool dry, lacks lubrication . . . . . . . . . . .Use BOSTITCH Air Tool Lubricant
O-rings/seals cut or cracked . . . . . . . .Replace O-rings/seals
Exhaust blocked . . . . . . . . . . . . . . . . .Check bumper, head valve spring, muffler
Trigger assembly worn/leaks . . . . . . . .Replace trigger assembly
Dirt/tar build up on driver . . . . . . . . . . .Disassemble nose/driver to clean
A
ir pressure too low . . . . . . . . . . . . . . .Check air supply equipment
Worn or misadjusted cycle lever . . . . .Adjust adjustment nut or replace adjustment lever
S
kipping fasteners; intermittent feed Tar/dirt in driver channel . . . . . . . . . . . .Disassemble and clean nose and driver
Air restriction/inadequate air
flow through quick disconnect
socket and plug . . . . . . . . . . . . . . . . . .Replace quick disconnect fittings
Worn piston O-ring /piston . . . . . . . . . .Replace O-ring/piston
Tool dry, lacks lubrication . . . . . . . . . . .Use BOSTITCH Air Tool Lubricant
Low air pressure . . . . . . . . . . . . . . . . . .Check air supply system to tool
Loose magazine nose screws . . . . . . .Tighten all screws
Leaking head cap gasket . . . . . . . . . .Tighten screws/replace gasket
Trigger valve O-ring cut/worn . . . . . . . .Replace O-ring
Broken/chipped driver . . . . . . . . . . . . .Replace driver (check piston O-ring)
Worn anvil/pusher . . . . . . . . . . . . . . . . .Replace anvil/pusher
Broken pusher spring . . . . . . . . . . . . . .Replace pusher spring
Worn former . . . . . . . . . . . . . . . . . . . . .Replace former
Dry/dirty magazine . . . . . . . . . . . . . . . .Clean/lubricate use BOSTITH Air Tool Lubricant
Fasteners jam in tool Driver channel worn . . . . . . . . . . . . . . .Replace nose/check door
Wrong size fasteners . . . . . . . . . . . . . .Use only recommended fasteners
Bent fasteners . . . . . . . . . . . . . . . . . . .Discontinue using these fasteners
Loose magazine/nose screws . . . . . . .Tighten all screws
Broken/chipped driver . . . . . . . . . . . . .Replace driver
Worn former . . . . . . . . . . . . . . . . . . . . .Replace former
Worn anvil/pusher . . . . . . . . . . . . . . . . .Replace pusher

Bostitch D62ADC Specifications

General

Brand	Bostitch
Model	D62ADC
Category	Power Tool
Language	English