Brother DCP-1617NW

To Next Page

To Previous Page

2-312-31

 Confidential Confidential

 

7.7.88 MoModedem PCm PCB AB ASSSSY (oY (onlnly foy for mr mododelels wis with mth mododem em PCPCB)B)

(1)(1) DiscoDisconnect thnnect the modem e modem PCB flat PCB flat cable fcable from the marom the main PCB ASSYin PCB ASSY..

(2)(2) RemovRemove the tapte the taptite pan B M4ite pan B M4x12 DA scrx12 DA screw and the tew and the taptite cuaptite cup S M3x8 SR scrp S M3x8 SR screw toew to

remove the upper modem shield plate from the machine.remove the upper modem shield plate from the machine.

(3)(3) RemovRemove the two scre the two screw pan (S/ew pan (S/P washer) MP washer) M3.5x6 sc3.5x6 screws to remrews to remove the loove the lower modemwer modem

shield plate from the machine.shield plate from the machine.

(4)(4) RemovRemove the screw pe the screw pan (S/P washan (S/P washer) M3.5xer) M3.5x6 and the ta6 and the taptite binptite bind B M4x12 scd B M4x12 screw torew to

remove the SDAA shield plate from the machine.remove the SDAA shield plate from the machine.

(5)(5) Remove Remove the SDAthe SDAA shielA shield coved cover HS frr HS from the om the SDAA shSDAA shield pield plate.late.

(6)(6) RemovRemove the two tae the two taptite cuptite cup S M3x8 SR scrp S M3x8 SR screws to remews to remove the modove the modem PCB ASSY and them PCB ASSY and thee

SDAA insulation sheet from the SDAA shield plate.SDAA insulation sheet from the SDAA shield plate.

Fig. 2-27Fig. 2-27

Note:Note:

•• After disAfter disconnecconnecting the flat cating the flat cable, checble, check that the cable is not damk that the cable is not damaged at its end oraged at its end or

short-circuited. When connecting the flat cable, do not insert it at an angle. Aftershort-circuited. When connecting the flat cable, do not insert it at an angle. After

insertion, check that the cable is not at an angle.insertion, check that the cable is not at an angle.

Assembling Note:Assembling Note:

•• Be carefBe careful not tul not to assembo assemble witle with wrong sh wrong screwscrews..

•• Secure the maiSecure the main PCB insulan PCB insulation sheet and the upper motion sheet and the upper modem shield platdem shield plate with the screw "A".e with the screw "A".

•• Make sure to attMake sure to attach insulation sheet. Failure ach insulation sheet. Failure to attach the insulatto attach the insulation sheet can result iion sheet can result in firen fire

or electrical shock.or electrical shock.

Modem PCBModem PCB

flat cableflat cable

Taptite cup S M3x8 SRTaptite cup S M3x8 SR

SDAA shield plateSDAA shield plate

SDAA insulation sheetSDAA insulation sheet

Modem PCB ASSYModem PCB ASSY

SDAA shield cover HSSDAA shield cover HS

Taptite bind B M4x12Taptite bind B M4x12

Screw pan (S/P washer) M3.5x6Screw pan (S/P washer) M3.5x6

Screw pan (S/P washer)Screw pan (S/P washer)

M3.5x6M3.5x6