EasyManuals Logo

Brother HL-L2300D Service Manual

Brother HL-L2300D
205 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #37 background imageLoading...
Page #37 background image
2-19
Confidential
3.3 LED Display (LED Models)
3.3.1 LED display when operator call occurs
Details of the message can be determined by the combination of the LEDs. Refer to the page
shown in the "Refer to:" column in the table below to take appropriate measures. Most errors
are automatically cleared after measures are taken. If not automatically cleared, press the
[Go] key to reset the machine.
LED status in the table below: : Unlit : Lit : Flashing
LED Type of problem
Error
codes
Refer
to:
The eject sensor detected that the fuser cover was
open.
6004 2-35
The eject sensor does not detect paper pass after
the registration rear sensor detected the paper pass.
7000 2-39
The eject sensor remains ON (paper pass detected)
even after the registration rear sensor detected the
end of paper pass.
7100 2-40
When printing from the paper tray, the registration
front sensor does not detect paper pass within the
specified time after the paper feed sensor detected
paper pass.
7300 2-40
The registration front sensor does not detect paper
pass within the specified time after the first side was
printed in duplex printing mode.
7700 2-41
The eject sensor was ON when the power switch
was turned ON.
7C00 2-41
First side printing started before finishing receiving
the second side data in duplex printing mode due to
the insufficient memory.
8000 2-42
The back cover/duplex tray sensor detected that the
cover was open when duplex printing is started.
(Before registering printing data to engine)
8903 2-42
The back cover/duplex tray sensor detected that the
cover was open during duplex printing. (After
registering printing data to engine)
8904 2-42
The registration rear sensor detected that the paper
fed was smaller or larger than the specified size in
duplex printing mode.
8A01 2-43
When printing from the paper tray, the size of paper
set in the paper tray does not match the size
specified by the driver.
9002 2-44
A tray set to duplex printing-incompatible size was
specified in duplex printing.
9701 2-44
There is insufficient memory to expand PC print
data.
C700 2-45

Table of Contents

Other manuals for Brother HL-L2300D

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Brother HL-L2300D and is the answer not in the manual?

Brother HL-L2300D Specifications

General IconGeneral
ColorNo
N-up printing2, 4, 6, 9, 16, 25
Duplex printingYes
Print technologyLaser
Maximum resolution2400 x 600 DPI
Duplex printing modeAuto
Print speed (black, normal quality, A4/US Letter)26 ppm
Duplex print speed (black, normal quality, A4/US Letter)6.5 ppm
Printing colorsBlack
Maximum duty cycle10000 pages per month
Recommended duty cycle250 - 2000 pages per month
Number of print cartridges1
Page description languagesGDI
Paper input typePaper tray
Total input capacity250 sheets
Total output capacity100 sheets
Multi-Purpose tray input capacity1 sheets
Custom media width76.2 - 215.9 mm
Maximum print size210 x 297 mm
Custom media length127 - 355.6 mm
Paper tray media typesBond paper, Envelopes, Labels, Plain paper, Recycled paper, Thick paper, Thicker paper, Thin paper
Paper tray media weight60 - 105 g/m²
Non-ISO print media sizesExecutive (184 x 267mm), Letter (media size)
ISO A-series sizes (A0...A9)A4, A5, A6
JIS B-series sizes (B0...B9)B5
Maximum ISO A-series paper sizeA4
Multi-Purpose Tray media weight60 - 163 g/m²
Mobile printing technologiesNot supported
Standard interfacesUSB 1.1, USB 2.0
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Processor familyARM Cortex
Noise level (idle)30 dB
Maximum internal memory- MB
Sound pressure level (printing)49 dB
Sound pressure level (quiet mode)45 dB
DisplayLED
CertificationNordic Swan
Display number of lines1 lines
AC input voltage220 - 240 V
AC input frequency50 - 60 Hz
Power consumption (max)1080 W
Power consumption (off)0.06 W
Power consumption (standby)58 W
Power consumption (printing)455 W
Power consumption (PowerSave)5.4 W
Sustainability certificatesBlue Angel, ENERGY STAR
Minimum storage drive space80 MB
Mac operating systems supportedMac OS X 10.7 Lion, Mac OS X 10.8 Mountain Lion, Mac OS X 10.9 Mavericks
Server operating systems supportedWindows Server 2003, Windows Server 2003 x64, Windows Server 2008, Windows Server 2008 R2, Windows Server 2008 x64, Windows Server 2012, Windows Server 2012 R2
Windows operating systems supportedWindows 7 Home Basic, Windows 7 Home Basic x64, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional, Windows 7 Professional x64, Windows 7 Starter, Windows 7 Starter x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows 8, Windows 8 Enterprise, Windows 8 Enterprise x64, Windows 8 Pro, Windows 8 Pro x64, Windows 8 x64, Windows 8.1, Windows 8.1 Enterprise, Windows 8.1 Enterprise x64, Windows 8.1 Pro, Windows 8.1 Pro x64, Windows 8.1 x64, Windows Vista Business, Windows Vista Business x64, Windows Vista Enterprise, Windows Vista Enterprise x64, Windows Vista Home Basic, Windows Vista Home Basic x64, Windows Vista Home Premium, Windows Vista Home Premium x64, Windows Vista Ultimate, Windows Vista Ultimate x64, Windows XP Home, Windows XP Home x64, Windows XP Professional, Windows XP Professional x64
Storage temperature (T-T)0 - 40 °C
Operating temperature (T-T)10 - 32 °C
Storage relative humidity (H-H)10 - 90 %
Operating relative humidity (H-H)20 - 80 %
Package depth441 mm
Package width286 mm
Package height504 mm
Package weight8000 g
Cables includedAC
Weight and Dimensions IconWeight and Dimensions
Depth356 mm
Width360 mm
Height183 mm

Related product manuals