Brother MFC-J410W User Manual

13
27 This equipment is not capable, under all operating conditions, of correct operation at the higher
speeds for which it is designed. Telecom will accept no responsibility should difficulties arise
in such circumstances. This condition typically applies to 56 kbit/s modems and facsimile
machines operating at >14.4 kbit/s.
28 When using the Caller Line Identification incorporated in this device, verify the integrity of the
recorded digits prior to dialling.
29 Some parameters required for compliance with Telecom’s Telepermit requirements are
dependent on the equipment (PC) associated with this device. The associated equipment shall
be set to operate within the following limits for compliance with Telecom’s Specifications:
 There shall be no more than 10 call attempts to the same number within any 30 minute
period for any single manual call initiation.
 The equipment shall go on-hook for a period of not less than 30 seconds between the end
of one attempt and the beginning of the next call attempt.
 Automatic calls to different numbers are spaced such that there is not less than 5 seconds
between the end of one call attempt and the beginning of another.
 Equipment shall be set to ensure that calls are answered within 3 and 30 seconds of the
receipt of ringing.
30 In the event of any problem with this device, it is to be disconnected, and a CPE item connected
to one of its terminal ports may be connected directly in its place.
The user should then arrange for the product to be repaired. Should the matter be reported to
Telecom as a wiring fault and the fault is proven to be due to this product, a call out charge will
be incurred by the customer.
31 The Caller ID telephone numbers that are displayed and stored in this equipment include the
caller’s area code but not the toll access “0” prefix. When calling back it is necessary to add a
“0” to the telephone number, or if the telephone number is a local number, omit the area code
digit. If the toll services of a service provider other than Telecom are being used then a toll
charge may be incurred if the “0” prefix toll access code and area code are used.

Brother MFC-J410W Specifications

General

Dimensions (WxDxH)	390 x 370 x 180 mm
All-in-one functions	Copy, Fax, Print, Scan
Color all-in-one functions	copy, fax, print, scan
Duplex printing	No
Print technology	Inkjet
Maximum resolution	1200 x 6000 DPI
Print speed (black, normal quality, A4/US Letter)	33 ppm
Print speed (color, normal quality, A4/US Letter)	27 ppm
Maximum duty cycle	- pages per month
Copier resize	25 - 400 %
Maximum copy resolution	1200 x 1200 DPI
Maximum number of copies	99 copies
Grayscale levels	256
Input color depth	36 bit
Output color depth	24 bit
Image formats supported	JPG, TIF
Optical scanning resolution	1200 x 2400 DPI
Faxing	Color faxing
Fax memory	170 pages
Modem speed	14.4 Kbit/s
Total input capacity	100 sheets
Total output capacity	50 sheets
Auto document feeder (ADF)	Yes
Auto document feeder (ADF) input capacity	15 sheets
Envelopes sizes	10, C5
Maximum print size	216 x 356 mm
Paper tray media types	Coated paper, Envelopes, Glossy paper, Plain paper, Transparencies
ISO A-series sizes (A0...A9)	A4, A5, A6
JIS B-series sizes (B0...B9)	B5
Photo paper sizes (imperial)	4x6, 5x7 \
Borderless printing media sizes	4x6, 5x7, A4, Letter
Maximum ISO A-series paper size	A4
Display	-
Market positioning	Home & office
Standard interfaces	USB 2.0, Wireless LAN
USB 2.0 ports quantity	1
Internal memory	32 MB
Compatible memory cards	Memory Stick (MS), MS Duo, MS PRO, MS PRO Duo
Sound pressure level (printing)	50 dB
Power consumption (off)	0.65 W
Power consumption (standby)	4 W
Power consumption (average operating)	19 W
Operating temperature (T-T)	10 - 35 °C
Operating relative humidity (H-H)	20 - 80 %
Sustainability certificates	ENERGY STAR