Brush Wolf 7201 - 4800 Low Flow & Standard Parts List

— 17 — www.brushwolf.com
4800 Model Parts List
ITEM ITEM QTY PART NUMBER DESCRIPTION
1 1
15054
PLATE, ACCESS, 2 HOLE, 5.250 X 3.250 X 0.250
2 1
15067
GUARD, COUPLING, BW, STD
3 1
15109
ROD, ROUND, 0.375 X 47.000
4 1
15133
DECAL KIT, BW 4800
5 1
15597
HOSE WHIP ASSEMBLY, -8 ORFS, FEMALE SWIVEL COUPLINGS, 0.750 X 78.000 HOSE
6 1 15632
WELDMENT FRAME BW 4800
7 1 15652
ASSEMBLY BLADE CARRIER, BW 4800
8 36
15068
CHAIN, 0.313, 5 LINK, PROOF COIL
9 1
15078
COUPLER, FLAT FACED, FEMALE, 3/4
10 1 15079
COUPLER , FLAT FACED, MALE, 3/4
11 1 15093
GEARBOX, 62HP, 1:1.93 RATIO
12 1 15123
COUPLING, STD, 1.250 MOTOR, 1.375 GB, 5.500
13 1 15248
CLAMP, BODY, TWO PIECE, 30MM, TWO HOSE
14 1 15249
COVER PLATE, CLAMP, 30MM, TWO HOSE
15 1 15353*
STANDARD FLOW BRUSH CUTTER - MOTOR, 6.2 CU IN, SAE “A” 2 BOLT, 7/8-14-12 SAE O-RING
PORTS, 1.250 DIA X 1.250 KEYED SHAFT, 3500/750 RELIEF, EATON
15 1 15352*
LOW FLOW (LF) BRUSH CUTTER - MOTOR, 4.9 CU IN, SAE “A” 2 BOLT, 7/8-14 SAE O-RING
PORTS, 1.250 DIA X 1.250 KEYED SHAFT, 3500/750 RELIEF, EATON
16 4 15584
ADAPTER, STRAIGHT, #8 MORFS, #10 MORB
17 2 Hardware
BOLT, HH, 1/2-13 X 2 UNC, GRD 5, ZINC
18 1 Hardware
BOLT, HH, 1/2-13 X 3/4 UNC, GRD 5, ZINC
19 1 15274**
BOLT, HH, 1/2-13 X 3, GRD 2, ZINC
20 1 Hardware
BOLT, HH, 5/16-18 X 2 1/2, GRD 5, ZINC
21 4 Hardware
BOLT, HH, 5/16-18 X 3/4, GRD 5, ZINC
22 4 Hardware
NUT, NYLOCK, 3/8-16, ZINC
23 3 Hardware
NUT, NYLOCK, 1/2-13, ZINC
24 4 Hardware
NUT, NYLOCK, 3/4-10, ZINC
25 2 Hardware
SET SCREW_CP_1_4-20X3_8 UNC
26 4 Hardware
WASHER, FLAT, 3/8, ZINC
27 4 Hardware
WASHER, FLAT, 5/16, ZINC
28 2 Hardware
WASHER, SPRING LOCK, .500, ZINC
29 5 Hardware
WASHER, SPRING LOCK, 5/16, ZINC
30 2 15381
WASHER, NORD-LOCK, 0.500 X 1.000 OD, ZINC
31 4 15379
WASHER, NORD-LOCK, 0.750 X 1.210 OD, ZINC
* DEPENDS ON MODEL OF BRUSH CUTTER
** SHEAR BOLT