Brush Wolf 7201 - 6000 Low Flow & Standard Parts List

— 19 — www.brushwolf.com
6000 Parts Diagram Low Flow & Standard
ITEM ITEM QTY PART NUMBER DESCRIPTION
1 1
15000
WELDMENT FRAME BW 6000
2 1
15054
PLATE, ACCESS, 2 HOLE, 5.250 X 3.250 X 0.250
3 1
15056
ASSEMBLY, BLADE CARRIER, BW 6000
4 1
15067
GUARD, COUPLING, BW, STD
5 1
15080
ROD, ROUND, 0.375 X 59.000
6 2
15597
HOSE WHIP ASSEMBLY, -8 ORFS, FEMALE SWIVEL COUPLINGS, 0.750 X 78.000 HOSE
7 1 15353*
STANDARD FLOW BRUSH CUTTER - MOTOR, 6.2 CU IN, SAE “A” 2 BOLT, 7/8-14-12 SAE O-RING
BO PORTS, 1.250 DIA X 1.250 KEYED SHAFT, 3500/750 RELIEF, EATON
7 1 15748*
LOW FLOW BRUSH CUTTER - MOTOR, 8.0 CU IN, SAE “A” 2 BOLT, 7/8-14 SAE O-RING PORTS,
1.250 DIA X 1.250 KEYED SHAFT, 3500/750 RELIEF, EATON
8 46
15068
CHAIN, 0.313, 5 LINK, PROOF COIL
9 1
15069
DECAL KIT, BW 6000
10 1 15078
COUPLER, FLAT FACED, FEMALE, 3/4
11 1 15079
COUPLER , FLAT FACED, MALE, 3/4
12 1 15092*
STANDARD FLOW BRUSH CUTTER - GEARBOX, 62HP, 1:1.46 RATIO
12 1 15093*
LOW FLOW BRUSH CUTTER - GEARBOX, 62HP, 1:1.93 RATIO
13 1 15123
COUPLING, STD, 1.250 MOTOR, 1.375 GB, 5.500
14 1 15248
CLAMP, BODY, TWO PIECE, 30MM, TWO HOSE
15 1 15249
COVER PLATE, CLAMP, 30MM, TWO HOSE
16 4 15584
ADAPTER, STRAIGHT, #8 MORFS, #10 MORB
17 4 Hardware
BOLT, HH, 5/16-18 X 3/4, GRD 5, ZINC
18 1 Hardware
BOLT, HH, 5/16-18 X 2 1/2, GRD 5, ZINC
19 1 Hardware
BOLT, HH, 1/2-13 X 3/4 UNC, GRD 5, ZINC
20 2 Hardware
BOLT, HH, 1/2-13 X 2 UNC, GRD 5, ZINC
21 1 15274**
BOLT, HH, 1/2-13 X 3, GRD 2, ZINC
22 4 Hardware
NUT, NYLOCK, 3/8-16, ZINC
23 3 Hardware
NUT, NYLOCK, 1/2-13, ZINC
24 4 Hardware
NUT, NYLOCK, 3/4-10, ZINC
25 2 Hardware
SET SCREW_CP_1_4-20X3_8 UNC
26 4 Hardware
WASHER, FLAT, 5/16, ZINC
27 4 Hardware
WASHER, FLAT, 3/8, ZINC
28 2 15381
WASHER, NORD-LOCK, 0.500 X 1.000 OD, ZINC
29 4 15379
WASHER, NORD-LOCK, 0.750 X 1.210 OD, ZINC
30 5 Hardware
WASHER, SPRING LOCK, 5/16, ZINC
31 2 Hardware
WASHER, SPRING LOCK, .500, ZINC
*
DEPENDS ON THE MODEL OF BRUSH CUTTER
** SHEAR BOLT