BullFrog A7 - Water Care Management; Water Care Operation Modes

17
Water Care
e Water Care submenu will help you set up your ideal ltration
and heating settings. Choose from Away, Standard/Beginner,
Energy Saving, Super Energy Saving, and Weekender, depending
on your needs. Touch the Water Care mode name to choose
your setting. A conrmation message will appear to prevent
inadvertent modication of spa water care settings. Touch the
check icon to conrm your choice or touch the X icon to decline.
In Economy modes, the set point will be reduced by 20°F*
(11°C), which means that the heating system will not be engaged
unless the temperature falls to 20°F (11°C) below the spa’s set
temperature.
e ltration schedule shown on the M Series, A Series or STIL
(A1000) screen will apply to the main ltration pump.
Water Care Operation Modes
NOTE: Your spa will come from the factory in "Super Energy
Savings" mode. See operation mode options below and select the
best mode for your anticipated usage.
Super Energy (factory default setting)
In Super Energy mode the spa temperature set point will be
reduced by 20°F (11°C) (see description of “Economy modes”
above) during peak daytime hours. Spa will heat to normal set
point during evening hours, every day of the week.
Suggested use: Use to save maximum energy and heat only
during set lter cycles.
Economy time: Will not use Economy mode, only heats during
ltration cycles.
Filter cycle start time: 8:00 AM, duration 1.5 hours and 8:00
PM, duration 1.5 hours.
Away
In Away mode the spa temperature set point will be reduced by
20°F (11°C) (see description of “Economy modes” above). Spa
will remain in Economy mode at all times of the day and all days
of the week.
Suggested use: Use when on vacation or not using the spa for
longer than 2 weeks.
Economy time: Everyday of the week, 24 hours per day.
Filter cycle start time: 8:00 PM, duration 3 hours.
Standard - Beginner
In Standard mode the spa will heat to the set point and lter
according to the spa’s standard conguration. Spa will heat to set
point at all times and all days of the week.
Suggested use: Use to maintain readiness for use everyday at all
times of day.
Economy time: Not an Economy mode.
Filter cycle start times: 8:00 AM, duration 1.5 hours and 8:00
PM, duration 1.5 hours.
Energy Saving
In Energy Saving mode the spa temperature set point will be
reduced by 20°F (11°C) (see description of “Economy modes”
above) during peak daytime hours. Spa will heat to normal set
point during evening hours and on the weekend.
Suggested use: Use to save energy during weekday daytime hours
and make ready for use at night and all day on weekends.
Economy time: Monday - Friday, 6:00 AM - 6:00 PM.
Filter cycle start time: 7:00 PM, duration 3 hours.
Weekender
In Weekender mode the spa temperature set point will be reduced
by 20°F (11°C) (see description of “Economy modes” above) from
Monday to Friday. Spa will heat to set point at all times on the
weekend (Saturday & Sunday).
Suggested use: Use when spa is used only on weekends and not
on weekdays.
Economy time: Monday - Friday, 24 hours per day.
Filter cycle start time: 8:00 AM, duration 1.5 hours and 8:00
PM, duration 1.5 hours.
Default Settings: e Default Settings option will restore all
Water Care modes and schedules to the spa’s default settings. You
will be asked to conrm your choice.
NOTE: Spas NOT equipped with a dedicated ltration pump
will turn on automatically, using jet pump 1 on low speed, to lter
and/or heat. is is normal spa operation.
NOTE: Your spa is equipped with a freeze-prevention system.
If potential freezing conditions are detected one or more jet
pumps will turn on automatically to circulate water and prevent
the possibility of freezing. is is normal operation.
Modifying Water Care Schedules
To modify a Water Care category, touch the pen icon at the right
of the desired Water Care option to open the submenu.
Touch the Economy tab to change the economy setting and
Filter cycle tab for the ltration settings (or schedules). You can
add economy or ltration schedules by touching the title labeled
“Add lter cycle” or “Add economy cycle”. To delete a schedule,
touch the garbage can icon at the right of the desired function
title. Conrm your action when prompted.
You can modify the programmed schedules by selecting one
and adjusting the schedule. You have several possibilities for
the schedule (Mon-Fri, weekend, every day, or single days). e
schedules will be repeated each week. e time and duration
are set in 30-minute increments. When changes are done, press
“conrm”. If you don’t want to keep any changes, press “cancel” or
use the calendar icon to go back. Ensure that you have selected
the desired Water Care mode in the main Water Care menu.