18
Maintenance Reminders
e M Series, A Series and STIL (A1000) keypad can be set up
to remind you of several types of maintenance required on your
spa, including rinsing the lter, cleaning the lter, changing spa
water, and 2-year professional maintenance checks. Each task has
its own standard duration, based on normal use, or you may adjust
to t your specic expected usage.
Access the Reminders submenu by pressing the Reminders icon
in the Settings menu.
Maintenance reminders allow you to verify the time left before
maintenance is required, as well as to reset the time once a task is
completed.
To reset a task, select it by pressing the title of the specic
reminder, then conrm when prompted. Once you have
conrmed, the task timer will be reset. You can also use the
option “Reset Reminders” to reset all the reminders.
Set Date and Time of Day
Setting the correct date and time is important for settings to
function as expected. Upon restarting your spa adjust the time
format (24 hr. or AM/PM), change the year, date, and time as
needed.
Within the Settings menu select “Date & Time” to access these
submenus.
Select “Set Date” to adjust the year, month and day. Swipe up and
down the column you want to change and select the desired value.
When you are done, touch the Settings icon to save.
Select “Set Time” to change the hour, minute and time format.
Swipe up and down the column you want to change and select
the desired value. When done, touch the Settings icon to save.
Keypad Settings
In the Keypad submenu you can change the temperature unit
settings or the language setting.
Change temperature units by touching the “Temperature Units”
title and then the desired unit of measurement.
Change the language setting by touching the “Language” title and
then selecting the desired language.
Standby/Lock
Standby mode allows you to service your spa. Pumps can be
stopped for 30 minutes in this mode, and will automatically
restart after. Select Standby mode by pressing the pause/standby
icon. e home/status screen and normal spa function will resume
after the 30 minute standby period.
e Lock option allows the user to partially or completely lock
the keypad. Selecting the “Lock” option will lock all functions on
the control while the “Partial Lock” option will allow jets, audio,
and lights to remain funtional. To lock the keypad select “Lock
Settings” then select “Lock” or “Partial Lock” according to the
functions you wish to lock. When asked, select a 4-digit code.
e same code will be needed to unlock the keypad. To lock the
keypad again, you will be prompted to select another 4-digit code.
e keypad can be unlocked with a universal unlock code (3732)
or by a reset of the keypad. When Full Lock is selected, all
functions are locked. In Partial Lock, you may activate accessories,
but spa settings may not be changed.
IMPORTANT: Please do not make changes in this section
unless you are a qualied electrician.
In this section you can change the low-level conguration, as
well as modify the number of phases and the input current
value.* Please refer to the diagram on the spa control center box,
located inside of the equipment compartment, for the default
conguration of your specic spa model. Once the modication is
completed, conrm selection when asked and touch the Settings
icon to return to the Settings menu.
NOTE: On initial connection the installer is prompted for
electrical congurations. e Low-Level setting is selected by the
installer. e Phase and Amperage is set automatically. Default
settings should be conrmed by the installer to match the actual
phase and amperage at the spa’s installation location. In rare
occassions it may be necessary to adjust the Phase and Amperage
setting to match the actual service availableat the installation
location using the instructions above.
* Depending on the pack conguration, a code may be required to
modify the low-level number. is code is 5555.
About
is section displays technical information about the M Series, A
Series or STIL (A1000) control software version and applicable
revisions of the dierent components of your system.
Automated Cover Functions (M
Series only)
M Series spas feature a cover with sensor technology as standard
equipment. is technology provides several automated/smart
functions for additional convenience and safety.
NOTE: Many of the M Series cover smart functions work
in conjunction with the optional Bullfrog Spas CloudControl
2 smartphone application. To take full advantage of sensor-
enabled smart functionality Cloud Control 2 must be installed
as an option on the spa and the Could Control 2 app must
be downloaded and installed on your smart device. Follow all
connection procedures and instructions available on the Bullfrog
Spas CloudControl 2 app.
Automatic On/O Lighting: When your M Series cover is
opened both interior and exterior lights will illuminate.
When you close your M Series cover both interior and
To Next Page
Loading...
