BWT AQUADIAL softlife 10

Questions and Answers

L
Lori HudsonAug 15, 2025
What to do if the water level in the brine cabinet of my BWT Water Dispenser is overflowing?
- S
  Sean EdwardsAug 15, 2025
  If the water level in the brine cabinet of your BWT Water Dispenser is overflowing, first check if the line pressure is within the specification (1.7 - 5.0 bar for the UK / 1.0 - 8.0 bar for EU) by connecting a pressure gauge to a water outlet. If the pressure falls outside this range, fit a pressure reducing valve or booster pump. Also, ensure that there is no flow through the drain line by checking if it is kinked, blocked, or frozen. Finally, verify that the power is on and the connections are secure, especially after a power interruption.
M
Michelle SmithAug 18, 2025
How to fix hard water issue with my BWT AQUADIAL softlife 10?
- T
  tonyanolanAug 19, 2025
  If the water from your BWT Water Dispenser still remains hard, you should: - Fill the brine cabinet with salt. - Switch the power on and check the connections. - Close the by-pass valve and open the inlet and outlet valves. - Reset the hardness if required.
J
Joshua MillerAug 21, 2025
What to do if my BWT AQUADIAL softlife 10 has no water?
- T
  terrelldanielAug 22, 2025
  If there is no water coming from your BWT Water Dispenser, make sure that the mains stop valve is open. Also, check that the inlet and outlet valves to the water softener are open.
N
Nicole WalkerAug 25, 2025
What to do if BWT AQUADIAL softlife 10 Water Dispenser displays error code Err 1?
- M
  Michael NelsonAug 26, 2025
  If the electronic display of your BWT Water Dispenser shows error code “Err 1“ and an audible alarm sounds, first ensure all connections are secure. Then, turn the power off for 10 seconds and turn it back on to allow the system to reset.
T
Tanya DavisAug 28, 2025
What does it mean when my BWT Water Dispenser shows SALt error?
- G
  Glenn VillaAug 28, 2025
  If the electronic display of your BWT Water Dispenser shows error code “SALt“ and an audible alarm sounds, refill the brine cabinet with salt. Then, press the [SET] key to reset the salt alarm to the full salt capacity.
S
samanthajacksonSep 1, 2025
How to fix hard water with my BWT AQUADIAL softlife 10?
- A
  Amy YorkSep 1, 2025
  If water still remains hard when using your BWT Water Dispenser, try the following: * Fill the brine cabinet with salt. * Switch the power on and check the connections. * Close the by-pass valve and open the inlet and outlet valves. * Reset the hardness if required.
C
Christopher JonesSep 4, 2025
Why is my BWT AQUADIAL softlife 10 Water Dispenser brine cabinet overflowing?
- J
  Jasmine RyanSep 4, 2025
  If the water level in the brine cabinet of your BWT Water Dispenser reaches overflow, make sure that: 1. The line pressure is within the water softener's specification. Connect a pressure gauge to a water outlet and check the pressure is between 1.7 - 5.0 bar for the UK / 1.0 - 8.0 bar for EU. 2. If the pressure falls outside the specification, fit a pressure reducing valve or booster pump as needed. 3. Check the drain line to ensure it is not kinked, blocked, or frozen. 4. Verify that the power is on and all connections are secure.
A
Amanda VillanuevaSep 7, 2025
Why is there no water coming from my BWT AQUADIAL softlife 10?
- K
  Kenneth BrandtSep 7, 2025
  If your BWT Water Dispenser has no water, ensure the mains stop valve is open. Also, check that the inlet and outlet valves to the water softener are open.
S
Sarah BuckSep 12, 2025
What to do if BWT Water Dispenser constantly drains water?
- I
  isabel61Sep 12, 2025
  If water runs from the drain constantly in your BWT Water Dispenser, first check if the unit is in recharge mode. If it is, this is normal; wait until the recharge is complete. Also, ensure there is no flow to drain in the service position.