BWT AQA drink Pro 20 HCS

Other manuals for BWT AQA drink Pro 20 HCS

Installation And Operation Instructions84 pages

Installation And Operating Instructions97 pages

Questions and Answers

B
barberalexisAug 16, 2025
Why is no water coming out of my BWT AQA drink Pro 20 HCS Water Dispenser?
- H
  Heidi FrancisAug 17, 2025
  If your BWT Water Dispenser isn't dispensing water, there might be a few reasons: * The water pressure in the supply may not be sufficient; in this case, increase the water pressure. * The filter cartridge may be blocked; if so, insert a new filter. * The device may not be connected to the power supply; ensure the device is connected to the power supply. If these steps don't resolve the issue, there may be a problem with the pressure regulation or the pump, and you should contact a service technician.
S
Scott RobinsonAug 22, 2025
Why is my BWT AQA drink Pro 20 HCS not dispensing enough water?
- M
  mendozachristianAug 22, 2025
  If your BWT Water Dispenser isn't dispensing enough water, it could be due to: * A blocked filter cartridge. Try inserting a new filter. * Low incoming water pressure. Check and increase the incoming water pressure if necessary.
R
Rachel WhitneyAug 25, 2025
Why can't I dispense CO2 from my BWT Water Dispenser?
- V
  Veronica WilliamsAug 26, 2025
  If your BWT Water Dispenser is unable to dispense CO2, consider these potential causes: * There may not be enough water in the tank; top up the water or refill the tank and check the device's pipework. * The CO2 on/off switch on the rear panel may be switched off; switch the CO2 on/off switch to on. If neither of these solutions work, there may be a defective pump, and you should contact a service technician.
W
watersheatherAug 27, 2025
Why is my BWT AQA drink Pro 20 HCS Water Dispenser not dispensing cold water?
- P
  Preston RichardsAug 27, 2025
  If your BWT Water Dispenser isn't dispensing cold water, here's what you can check: * Ensure the on/off switch for cooling (COLD) on the rear panel is switched on. * Check the water supply. If it is working, inspect the water pipework in the device. * If there is ice formation in the cold water tank, disconnect the device from the power supply, allow the ice to melt, then reconnect the device to the power supply or switch it off.
K
Kaitlin GreenAug 30, 2025
What to do if my BWT AQA drink Pro 20 HCS is not dispensing hot water?
- M
  Melissa CamposAug 30, 2025
  If your BWT Water Dispenser isn't dispensing hot water, check if the on-off switch on the rear for hot water (HOT) is switched on. If the switch is on and the problem persists, there may be an issue with the boiler, and you should contact a service technician.
B
Brian Lambert IIISep 2, 2025
What does it mean when the light is flashing at the water outlet of my BWT Water Dispenser?
- L
  Lisa ChapmanSep 2, 2025
  A flashing light at the water outlet of your BWT Water Dispenser indicates that the wastewater tank is full; empty the wastewater tank. If the problem persists, the leakage sensor may be activated, and you should contact a service technician.
T
tommy83Sep 5, 2025
How to make the cold water colder in my BWT AQA drink Pro 20 HCS Water Dispenser?
- J
  Jason StoneSep 5, 2025
  If the cold water from your BWT Water Dispenser isn't cold enough, check the thermostat and reduce the temperature if necessary.
N
Nicole CollinsSep 7, 2025
What to do if only CO2 comes out of my BWT AQA drink Pro 20 HCS?
- K
  Kayla AlvaradoSep 8, 2025
  If only CO2 escapes when you press the CO2 button on your BWT Water Dispenser, disconnect the device from the power supply for 30 seconds, then reconnect it and press the CO2 key again.
G
george64Sep 10, 2025
Why does the water from my BWT AQA drink Pro 20 HCS have low CO2?
- C
  Caroline CarrSep 12, 2025
  If the water from your BWT Water Dispenser contains too little CO2, consider the following: * The CO2 gas cylinder may be empty; replace it. * The CO2 tank may need venting; turn off the water and actuate the CO2 outlet until only gas escapes, then turn the water back on and allow the CO2 to refill. * The CO2 pressure may be insufficient; increase it to 4 bar. * The temperature setting may be too high; lower the thermostat setting because the higher the water temperature, the less CO2 can be absorbed.
L
Leah ClarkeSep 10, 2025
What does it mean when the UV LED indicator flashes on my BWT AQA drink Pro 20 HCS?
- T
  Theresa CraigSep 12, 2025
  If the UV LED indicator flashes on the control panel, an acoustic alarm sounds, and water cannot be dispensed from your BWT Water Dispenser, disconnect the device from the power supply and unplug the connection; plug it back in, then switch the device on again. If the UV lamp does not work, then disconnect the device from the power supply again and replace the UV lamp.

Summary

1. Scope of Delivery

2. Technical Characteristics

3. Use and Operating Principle

3.1 Intended Use

Defines the intended use and purpose of the AQA drink Pro 20 water dispenser.

3.2 Operating Principle and Functions

Explains the operating principle and functions of the AQA drink Pro 20, including water types.

3.3 Built-in UV System Function

Details the integrated UV system, its function, and indicator lights.

3.4 Optional Cabinet Stand

Describes the optional cabinet stand for the AQA drink Pro 20, its features and components.

4. Operation and Safety Instructions

4.1 Warranty and Disclaimer of Liability

Outlines warranty terms and BWT's disclaimer of liability for improper use or maintenance.

4.2 Operator Responsibility

Specifies responsibilities of the operating party regarding manual adherence and device safety.

4.3 License Agreement

Mentions copyright protection for the manual and unauthorized use restrictions.

4.4 Qualified Personnel

Emphasizes that only trained specialists should perform installation and maintenance.

5. Installation and Commissioning

5.1 Unpacking the AQA DRINK PRO 20 Purifier

Instructions for unpacking and checking the AQA drink Pro 20 for completeness and transport damage.

5.2 Preparing the AQA DRINK PRO 20 Purifier

Steps for preparing the purifier, including placement and drip tray setup for tabletop/floor versions.

5.3 Filter Installation

Guidance on installing the filter, recommending BWT filters for optimal performance.

5.4 Water Supply Connection and System Filling

Detailed steps for connecting to the water supply and initial system filling and priming.

5.5 CO2 Cylinder Installation;Replacement and Device Activation

Instructions for installing or replacing the CO2 cylinder and powering on the device.

5.6 Cooling Temperature Adjustment

How to adjust the cooling temperature, with a note on preventing icing.

6. Maintenance and Sanitary-Hygienic Treatment

6.1 Maintenance Frequency

Recommends service intervals for cleaning, filter replacement, and UV lamp changes.

6.2 Sanitary-Hygienic Treatment

Details required sanitation procedures and the importance of regular cleaning by trained personnel.

6.3 Idle Periods

Instructions for handling periods of inactivity, including draining and flushing the system.

6.4 UV Lamp Replacement

Step-by-step guide for safely replacing the UV lamp, including precautions.

7. Disposal

8. Troubleshooting

9. Hygiene Checklist for AQA DRINK PRO 20

10. Sanitary-Hygienic Treatment Protocol for AQA DRINK PRO 20

11.1 AQA DRINK PRO 20 HCS Cleaning and Disinfection

Initial Preparation and Reaction (Steps 1-4)

Covers preparing the filter, rinsing, and initial reaction of the disinfectant.

Carbonator and Water Line Procedures (Steps 5-10)

Details emptying the carbonator, rinsing water lines, and initial CO2 handling.

System Rinsing and Checks (Steps 10-14)

Describes CO2 discharge, ambient line rinsing, and UV function checks.

Boiler Draining and Refilling (Steps 15-18)

Instructions for draining the hot water boiler and refilling it.

Process Control (Steps 19-20)

Covers stopping the process and advancing to the next step.

11.2 AQA DRINK PRO 20 HCA Cleaning and Disinfection

Initial Preparation and Reaction (Steps 1-4)

Covers preparing the filter, rinsing, and initial reaction of the disinfectant.

Water Line Rinsing and CO2 Handling (Steps 5-6, 9-10)

Details rinsing water lines and CO2 discharge procedures.

System Rinsing and Boiler Preparation (Steps 11-14)

Describes line rinsing, reset, UV check, and boiler draining.

Boiler Refilling and Device Restart (Steps 15-18)

Instructions for draining water and refilling the boiler and ice bank.

Process Control (Steps 19-20)

Covers stopping the process and advancing to the next step.