BWT AQA drink Pro 20 HCS User Manual (English)

Other manuals for BWT AQA drink Pro 20 HCS

Manual24 pages

Installation And Operating Instructions97 pages

Questions and Answers:

B
barberalexisAug 16, 2025
Why is no water coming out of my BWT AQA drink Pro 20 HCS Water Dispenser?
- H
  Heidi FrancisAug 17, 2025
  If your BWT Water Dispenser isn't dispensing water, there might be a few reasons: * The water pressure in the supply may not be sufficient; in this case, increase the water pressure. * The filter cartridge may be blocked; if so, insert a new filter. * The device may not be connected to the power supply; ensure the device is connected to the power supply. If these steps don't resolve the issue, there may be a problem with the pressure regulation or the pump, and you should contact a service technician.
S
Scott RobinsonAug 22, 2025
Why is my BWT AQA drink Pro 20 HCS not dispensing enough water?
- M
  mendozachristianAug 22, 2025
  If your BWT Water Dispenser isn't dispensing enough water, it could be due to: * A blocked filter cartridge. Try inserting a new filter. * Low incoming water pressure. Check and increase the incoming water pressure if necessary.
R
Rachel WhitneyAug 25, 2025
Why can't I dispense CO2 from my BWT Water Dispenser?
- V
  Veronica WilliamsAug 26, 2025
  If your BWT Water Dispenser is unable to dispense CO2, consider these potential causes: * There may not be enough water in the tank; top up the water or refill the tank and check the device's pipework. * The CO2 on/off switch on the rear panel may be switched off; switch the CO2 on/off switch to on. If neither of these solutions work, there may be a defective pump, and you should contact a service technician.
W
watersheatherAug 27, 2025
Why is my BWT AQA drink Pro 20 HCS Water Dispenser not dispensing cold water?
- P
  Preston RichardsAug 27, 2025
  If your BWT Water Dispenser isn't dispensing cold water, here's what you can check: * Ensure the on/off switch for cooling (COLD) on the rear panel is switched on. * Check the water supply. If it is working, inspect the water pipework in the device. * If there is ice formation in the cold water tank, disconnect the device from the power supply, allow the ice to melt, then reconnect the device to the power supply or switch it off.
K
Kaitlin GreenAug 30, 2025
What to do if my BWT AQA drink Pro 20 HCS is not dispensing hot water?
- M
  Melissa CamposAug 30, 2025
  If your BWT Water Dispenser isn't dispensing hot water, check if the on-off switch on the rear for hot water (HOT) is switched on. If the switch is on and the problem persists, there may be an issue with the boiler, and you should contact a service technician.
B
Brian Lambert IIISep 2, 2025
What does it mean when the light is flashing at the water outlet of my BWT Water Dispenser?
- L
  Lisa ChapmanSep 2, 2025
  A flashing light at the water outlet of your BWT Water Dispenser indicates that the wastewater tank is full; empty the wastewater tank. If the problem persists, the leakage sensor may be activated, and you should contact a service technician.
T
tommy83Sep 5, 2025
How to make the cold water colder in my BWT AQA drink Pro 20 HCS Water Dispenser?
- J
  Jason StoneSep 5, 2025
  If the cold water from your BWT Water Dispenser isn't cold enough, check the thermostat and reduce the temperature if necessary.
N
Nicole CollinsSep 7, 2025
What to do if only CO2 comes out of my BWT AQA drink Pro 20 HCS?
- K
  Kayla AlvaradoSep 8, 2025
  If only CO2 escapes when you press the CO2 button on your BWT Water Dispenser, disconnect the device from the power supply for 30 seconds, then reconnect it and press the CO2 key again.
G
george64Sep 10, 2025
Why does the water from my BWT AQA drink Pro 20 HCS have low CO2?
- C
  Caroline CarrSep 12, 2025
  If the water from your BWT Water Dispenser contains too little CO2, consider the following: * The CO2 gas cylinder may be empty; replace it. * The CO2 tank may need venting; turn off the water and actuate the CO2 outlet until only gas escapes, then turn the water back on and allow the CO2 to refill. * The CO2 pressure may be insufficient; increase it to 4 bar. * The temperature setting may be too high; lower the thermostat setting because the higher the water temperature, the less CO2 can be absorbed.
L
Leah ClarkeSep 10, 2025
What does it mean when the UV LED indicator flashes on my BWT AQA drink Pro 20 HCS?
- T
  Theresa CraigSep 12, 2025
  If the UV LED indicator flashes on the control panel, an acoustic alarm sounds, and water cannot be dispensed from your BWT Water Dispenser, disconnect the device from the power supply and unplug the connection; plug it back in, then switch the device on again. If the UV lamp does not work, then disconnect the device from the power supply again and replace the UV lamp.