Caple PYR600 - Page 13

13Instruction manual PYR600Please keep this instruction manual for future reference
› Fix the bracket to the wall using the screws supplied (Fig.11).
› Lift up the internal chimney until it covers the bracket and secure it by xing the screws on
both sides (Fig.12).
RECIRCULATION VERSION
› The chimney sections are not necessary when using the hood in recirculation mode.
› An activated charcoal lter is required when recirculating. This is to be installed behind
the grease lter and slots into place (Fig.13). Charcoal Filter CAP47CF can be purchased
directly from www.caple.co.uk or by calling our sales ofce on 0117 938 1900. This should
be replaced according to the effective use of the hood at least once every 6 months.
CONTROL PANEL
A: Light switch on/off
B: Motor switch - speed 1 / OFF
C: Motor switch - speed 2
D: Motor switch - speed 3
E: Motor switch - speed 4
F: 10-minute timer
REAR DUCTED
To duct the appliance to the rear, remove the 18 screws from the motor support.
Take the metal support and motor out (Fig.11).
Rotate the motor to have the air outlet on the rear side and then fix the screws
previously removed (Fig.12).
RECIRCULATION VERSION
>Fix the bracket to the wall using the screws supplied (Fig.11).
>Lift up the internal chimney until it covers the bracket and secure it by fixing the screws
on both sides (Fig.12).
Fig.11
Fig.12
>e air outlet grill on top of Install th the hood. (Fig.13). The chimney sections are not
necessary when using the hood in recirculation mode.
>An activated charcoal filter is required when recirculating. This is to be installed behind
the grease filter and slots into place (Fig.14). Charcoal Filter CAP47CF can be purchased
directly from www.caple.co.uk or by calling our sales office on 0117 938 1900. This
should be replaced according to the effective use of the hood at least once every 6 months.
Fig.13
Fig.14
CONTROL PANEL
A: Light switch on/off
B: Motor switch - speed 1 / OFF
C: Motor switch - speed 2
D: Motor switch - speed 3
E: Motor switch - speed 4
F: 10-minute timer
REAR DUCTED
To duct the appliance to the rear, remove the 18 screws from the motor support.
Take the metal support and motor out (Fig.11).
Rotate the motor to have the air outlet on the rear side and then fix the screws
previously removed (Fig.12).
RECIRCULATION VERSION
>Fix the bracket to the wall using the screws supplied (Fig.11).
>Lift up the internal chimney until it covers the bracket and secure it by fixing the screws
on both sides (Fig.12).
Fig.11
Fig.12
>e air outlet grill on top of Install th the hood. (Fig.13). The chimney sections are not
necessary when using the hood in recirculation mode.
>An activated charcoal filter is required when recirculating. This is to be installed behind
the grease filter and slots into place (Fig.14). Charcoal Filter CAP47CF can be purchased
directly from www.caple.co.uk or by calling our sales office on 0117 938 1900. This
should be replaced according to the effective use of the hood at least once every 6 months.
Fig.13
Fig.14
CONTROL PANEL
A: Light switch on/off
B: Motor switch - speed 1 / OFF
C: Motor switch - speed 2
D: Motor switch - speed 3
E: Motor switch - speed 4
F: 10-minute timer
REAR DUCTED
To duct the appliance to the rear, remove the 18 screws from the motor support.
Take the metal support and motor out (Fig.11).
Rotate the motor to have the air outlet on the rear side and then fix the screws
previously removed (Fig.12).
RECIRCULATION VERSION
>Fix the bracket to the wall using the screws supplied (Fig.11).
>Lift up the internal chimney until it covers the bracket and secure it by fixing the screws
on both sides (Fig.12).
Fig.11
Fig.12
>e air outlet grill on top of Install th the hood. (Fig.13). The chimney sections are not
necessary when using the hood in recirculation mode.
>An activated charcoal filter is required when recirculating. This is to be installed behind
the grease filter and slots into place (Fig.14). Charcoal Filter CAP47CF can be purchased
directly from www.caple.co.uk or by calling our sales office on 0117 938 1900. This
should be replaced according to the effective use of the hood at least once every 6 months.
Fig.13
Fig.14