Carestream DENTAL CS 2100

Questions and Answers

K
Kathleen RomanAug 6, 2025
What to do if X-ray exposure is too light on Carestream DENTAL equipment?
- L
  Larry ThomasAug 6, 2025
  If your Carestream DENTAL equipment's X-ray emission works, but the exposure is too light or completely white, it could be due to several reasons. The generator might not be positioned correctly, so adjust its position. The exposure time may be too short, so increase it. Check if the development time is insufficient and increase it according to the manufacturer's instructions. The developer might be too cold, so heat it, or too old/diluted, so replace it. Also, ensure that the exposure time mode is correctly selected and reposition the receptor if it's not correctly placed. If the unit is not correctly installed, you should contact your representative.
J
Jose MilesAug 12, 2025
What causes dark X-ray images with Carestream DENTAL equipment?
- C
  Claire CraneAug 12, 2025
  If the X-ray emission works but the exposure is too dark on your Carestream DENTAL equipment, it could be due to several factors. The exposure time might be too long, so reduce it. Also, the development time could be excessive, so reduce it following the manufacturer's instructions. If the developer is too hot, cool it down, or if it's too concentrated, adjust the concentration or change the developer. Make sure that the exposure time mode is correctly selected.
K
Kimberly RiosAug 18, 2025
How to troubleshoot Carestream DENTAL equipment when nothing lights up?
- P
  Pamela RamirezAug 18, 2025
  If your Carestream DENTAL equipment isn't lighting up, make sure the unit power switch is turned ON. Also, check if the unit is properly connected to the power supply cable and ensure the circuit breaker is ON.
C
Connie JacksonAug 25, 2025
Why is there no X-ray emission from my Carestream DENTAL equipment?
- N
  Natasha FosterAug 25, 2025
  If there is no X-ray emission from your Carestream DENTAL equipment, it might be because the generator is cooling down. Wait until the I01 message is no longer displayed. If the issue persists, the X-ray exposure button may be defective, and you should contact your representative.
N
Nicole BarrAug 30, 2025
What to do if the control unit of Carestream DENTAL equipment doesn't light up?
- M
  Michelle ColonAug 30, 2025
  If the control unit of your Carestream DENTAL equipment doesn't light up, it might be defective or disconnected. In this case, it is recommended to contact your representative for assistance.

Summary

About This Guide

Conventions in this Guide

Explains special messages and symbols used in the guide.

CS 2100 System Overview

General Overview

Provides a general description of the CS 2100 unit and its components.

CS 2100 Unit Configurations

Details the different configurations of the CS 2100 unit.

Control Timer Unit

Explains the functions and components of the control timer unit.

CS 2100 Radiology Process

Positioning

Guides on positioning the patient and the X-ray generator.

Exposure

Details exposure parameters, times, and related factors.

Acquiring an Image

Preparing for Image Acquisition

Steps to prepare the unit for taking an X-ray image.

Launching the X-Ray

Instructions on how to initiate the X-ray exposure process.

User Mode

Parameters

Lists configurable parameters and their options.

Entering the User Mode

Steps to access and navigate the user mode settings.

Modifying Parameters

Instructions for changing parameter values in user mode.

Exiting the User Mode

Procedure to exit the user mode and return to operational state.

Performing a Tube Seasoning

Details automatic and manual procedures for warming up the X-ray tube.

Troubleshooting

Quick Troubleshooting

Provides a table of common malfunctions and their solutions.

Information Messages

Explains informational codes and their meanings/actions.

Error Messages

Lists error codes, possible causes, and corrective actions.

Maintenance

Quarterly

Maintenance checks to be performed on a quarterly basis.

Annually

Maintenance checks and inspections recommended annually.

Cleaning and Disinfecting the CS 2100

Procedures for cleaning and disinfecting the equipment.

Contact Information

Manufacturers Address

Provides the official address of the manufacturer, Carestream Health, Inc.

Authorized Representatives

Lists authorized representatives in the European Community and Brazil.

Carestream DENTAL CS 2100 Specifications

General

Tube Voltage	60 kV
Tube Current	7 mA
Focal Spot	0.7 mm
Sensor Type	CMOS
Pixel Size	20 μm
Total Filtration	2 mm Al
Timer	0.01 to 2.00 seconds
Exposure Time Range	0.01 to 2.00 seconds
Power Source	AC 110-240V, 50/60 Hz