Need help?Do you have a question about the Case CX180C and is the answer not in the manual?
General| Bucket Breakout Force | 125 kN |
|---|---|
| Max Dig Depth | 6, 580 mm |
| Max Reach Along Ground | 9.87 m |
| Width | 2, 800 mm |
| Transport Width | 2.80 m |
| Digging Depth | 5460 mm |
| Max Digging Depth | 5460 mm |
Important notice about qualifications, tools, and liability for repair and maintenance.
Safety alert symbol and signal words (DANGER, WARNING, CAUTION) for personal safety.
Safety guidelines for cleaning, inspection, bearings, gears, seals, and service parts.
Prohibits modifications to the cab's protective structure to maintain operator safety.
Guidelines for safe use and disposal of fluids, lubricants, and batteries to protect the environment.
Table of tightening torques for various bolt sizes and types, including Loctite use.
Lists specific torque values for critical components and notes on Loctite application.
Guidance on shimming, shaft seals, O-rings, sealing compounds, and spare parts.
Precautions to prevent damage to electronic systems during charging and welding operations.
Importance and benefits of using specified special tools for efficient and reliable repairs.
Explains how contamination enters the hydraulic system and its potential problems.
Details on engine type, model, displacement, power, torque, and cooling.
Technical data for hydraulic pumps, pressure, flow rates, and control systems.
Components of the electrical system, including engine control, monitor system, and wiring.
Description of the operator's cab design, suspension, and interior features.
Technical details of the undercarriage, including travel motors, brakes, and track components.
Information on operating, shipping, counterweight, and ground pressure mass.
Arm and bucket digging force values according to ISO 6015 standard.
Dimensional data for the excavator with a 2.62 m (8.5958 ft) standard arm.
Dimensional data for the excavator with a 2.23 m (7.3163 ft) short arm.
Dimensional data for the excavator with a 3.05 m (10.0066 ft) long arm.
Details on travel unit, upper roller, lower roller, recoil spring, and shoes.
Specifications for swing unit, turntable bearing, counterweight, and engine.
Technical details for the muffler and air cleaner systems.
Specifications for the radiator, oil cooler, and hydraulic pumps.
Information on control valve manufacturer and maximum flow.
Characteristic diagrams for operation and travel remote control valves.
Specifications for cushion valve and center joint, including port sizes and operating pressure.
Specifications for boom, arm, and bucket cylinders, including bore and stroke.
Breakdown of machine weight by component, including operating and attachment weights.
Weights of individual components like travel unit, engine, hydraulic pump, and boom.
Weights for different arm configurations (standard, long, short).
Tables for converting units between gravitational and SI systems.
Conversion charts for millimeters to inches, square inches to square centimeters.
Conversion tables for US gallons to liters, Imperial gallons to liters, and pounds to kilograms.
Conversion tables for pressure (kPa to kgf/cm²) and torque (kgf·m to N·m).
Table for converting Fahrenheit temperatures to Centigrade.
Table for converting Centigrade temperatures to Fahrenheit.
List of recommended fluids and lubricants for fuel, engine oil, coolant, hydraulic oil, and grease.
Guidelines for using OAT-based coolant, mixing ratios, and water quality requirements.
Recommendations for diesel fuel type, quality, and proper fuel storage practices.
Instructions for environmentally sound disposal of used fluids, lubricants, and spare parts.
List of common abbreviations and their explanations from A to E.
List of common abbreviations and their explanations from F to R.
List of common abbreviations and their explanations from S to WOT.
Information on the machine's designation, serial number, and engine details.
Details on compliance with ISO standards for Roll Over Protective Structure (ROPS) and Falling Objects.
Places to record serial numbers for hydraulic pump, gears, and control valves.
To Next Page
