Cassese 910 JR - User Manual

Questions and Answers

A
Abigail MitchellAug 14, 2025
What to do if wedges do not penetrate into the wood with Cassese 910 JR Industrial Equipment?
- J
  Jenny HillAug 14, 2025
  If wedges do not penetrate into the wood when using Cassese Industrial Equipment, several factors could be at play. You might be using incorrect wedges, so switch to hard wood wedges. Check the pressure gauge readings, as inadequate stapling pressure can be a cause. Ensure the plunger speed and wedge firing are synchronized, adjusting button T clockwise if needed. For small mouldings, use side bars, as the plunger might be resting on fences M&N instead of contacting the moulding. A broken hammer, a clogged sub-assembly, or a broken/over-extended tension spring could also be responsible; replace the hammer or spring (PART 6520), or have the hammer cleaned. Finally, check the compressor pressure and hose connections, including the foot-pedal, in case there's a loss of pressure during firing.
M
melinda10Aug 17, 2025
What to do if the wedges will not fire on Cassese Industrial Equipment?
- C
  Christopher MarquezAug 18, 2025
  If wedges will not fire in your Cassese Industrial Equipment, it could be due to several reasons. First, check if the cartridge is empty and insert a full one if needed. If the cartridge is not empty, it might be incorrectly positioned; withdraw wire F, fully position the cartridge, and gently release. Finally, the hammer might be broken, in which case it needs to be replaced.
A
Anthony BrewerAug 21, 2025
Why does the press leave a mark on the mouldings when using Cassese 910 JR?
- J
  James GrahamAug 21, 2025
  If the press leaves a mark on the mouldings when using Cassese Industrial Equipment, this could be due to several reasons. The plunger might be descending too fast, so repeat the setting of the top pressor descent speed. The distance between the plunger and the moulding might be too large, so repeat the distance setting. Also, if the moulding is delicate, repeat the distance setting and use the joining jigs.
J
Jessica PetersonAug 25, 2025
What to do if wedges will not stack in Cassese Industrial Equipment?
- M
  morgancaldwellAug 25, 2025
  If wedges will not stack when using Cassese Industrial Equipment, several factors could be the cause. The wedge might be incorrectly positioned in the moulding, causing it to tilt and preventing stacking; repeat the setting of the stapling position. The hammer might be blunt or jagged, producing a dry clattering noise during stapling, in which case you should replace it. If you are trying to stack in hardwoods, use taller wedges (HW). A serious drop of pressure in the compressor, a defect in the blow-off valve, or a significant inaccuracy in the pressure gauge needle could also be responsible; in this case, replace the blow-off valve.
T
Tanner HarperAug 27, 2025
Why is the left moulding not clamped on Cassese 910 JR?
- G
  Gabriela FoxAug 27, 2025
  If the left moulding is not clamped when using Cassese Industrial Equipment, it could be due to a couple of reasons. The clamp setting might be incorrect, so repeat the setting of the moulding clamp with lever H. Alternatively, the assembly angle might be too wide, so repeat the setting of the assembly angle.
J
Juan SmithAug 30, 2025
How to fix an open top angle of corner on Cassese Industrial Equipment?
- J
  Joshua RoseAug 31, 2025
  If the top angle of the corner is open when using Cassese Industrial Equipment, it may be that the plunger speed and wedge firing are not synchronized. To resolve this, repeat the setting of the synchronization button, turning it a little clockwise.
S
Stephanie PerrySep 3, 2025
What to do if the right moulding is not clamped in Cassese Industrial Equipment?
- S
  Sarah McdonaldSep 3, 2025
  If the right moulding is not clamped when using Cassese Industrial Equipment, it might be due to excessive distance between the moulding and the clamp. To fix this, repeat the setting of the operating lever using lever H.
N
Nicholas MillerSep 6, 2025
Why is the angle open above or below on Cassese Industrial Equipment?
- E
  Emily ColemanSep 6, 2025
  If the angle is open above or below when using Cassese Industrial Equipment, the incorrect setting of back fences M & N could be the cause. Repeat the setting of the two fences M & N to resolve this.
S
Sandra BarberSep 9, 2025
What to do if the clamp does not clamp the moulding on Cassese Industrial Equipment?
- A
  allisontaylorSep 9, 2025
  If the clamp does not clamp the moulding when using Cassese Industrial Equipment, the moulding clamp setting is likely incorrect. Repeat the setting and ensure clamping of operating lever 1.