EasyManua.ls Logo

CDA ci261 - User Manual

CDA ci261
32 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
ci261 Freestanding Washing
Machine
Manual for Installation, Use and Maintenance

Questions and Answers

  • F
    Frank DavisAug 8, 2025
    How to start CDA ci261?
    • T
      Traci CarpenterAug 9, 2025
      If your CDA Washer doesn't start, make sure to press the ‘Start/Pause’ button. Also, ensure the ‘Programme Control’ knob is switched to the desired position, the machine door is properly closed, and the tap is turned on.
  • A
    anthonycruzAug 13, 2025
    Why is my CDA ci261 Washer vibrating?
    • J
      Jason DavisAug 13, 2025
      If your CDA Washer is vibrating, ensure that the feet of the machine are properly adjusted and that the transit bolts have been removed. Avoid overloading the machine and ensure the load is evenly distributed. Also, make sure there is at least 2cm of space between the machine and any walls or hard surfaces.
  • H
    helen15Aug 18, 2025
    What to do if my CDA ci261 Washer does not take in water?
    • J
      Joshua ButlerAug 18, 2025
      If your CDA Washer isn't taking in water, check the water inlet hose to ensure it isn't twisted or blocked. Also, clean the inlet filters and make sure the machine door is closed properly.
  • A
    Andrew PittsAug 23, 2025
    What to do if my CDA ci261 does not discharge water?
    • E
      Erin NelsonAug 25, 2025
      If your CDA Washer does not discharge water, try the following: * Clean the pump filter to remove any blockages. * Spread the load out within the machine to ensure it's balanced.
  • E
    Elizabeth DominguezAug 28, 2025
    Why does my CDA ci261 Washer empty water immediately after filling?
    • C
      Christopher TorresAug 29, 2025
      If your CDA Washer empties as soon as it fills with water, it's likely that the end of the water discharge hose is too low. Adjust the discharge hose to the appropriate height.
  • D
    donald42Sep 2, 2025
    Why is there excessive foam in my CDA ci261 Washer detergent drawer?
    • L
      lbruceSep 2, 2025
      If excessive foam forms in the detergent drawer of your CDA Washer, it's likely due to using too much or the wrong type of detergent. Press the “Start/Pause” button. To eliminate foam formation, mix a spoon of softener with a half litre of water and pour the mixture into the detergent drawer. After 5-10 minutes, press the “Start/Pause” button again. When washing next time, reduce the amount of detergent used, and ensure you're only using detergents specifically designed for automatic washing machines.

Summary

Important Safety and Appliance Information

General Safety Warnings

Operational Warnings

Before First Use and Garment Preparation

Detergents and Additives

Control Panel Overview

Starting a Wash Programme

Programme Selection

Details on how to choose the correct wash programme using the control knob and understanding the display.

Spin Speed Selection

Instructions on adjusting the spin speed, including reducing or disabling it for specific laundry needs.

Programme Listing

Display Fault Codes

Care and Maintenance Overview

Water Inlet Filters

Procedure for cleaning the water inlet filters to ensure proper water supply and prevent blockages.

Pump Filter Maintenance

Detergent Drawer and Exterior Cleaning

Installation and Transit Bolt Removal

Levelling the Appliance

Water and Drainage Connections

Electrical Safety and Fuse Replacement

Technical Specifications

Troubleshooting Common Issues

Troubleshooting Vibration and Foam Issues

Troubleshooting Washing Results and Spin Cycles

CDA ci261 Specifications

General IconGeneral
ColourWhite
Maximum Spin Speed (RPM)1200
Spin Efficiency ClassB
Washing Capacity (kg)6
Noise Level Washing (dB)58
Noise Level Spinning (dB)78
Number of Programmes15
Quick WashYes
Height (mm)850

Related product manuals