14
• CEDIMA® • Technical Documentation • All rights reserved according to ISO 16016 • Changes serving technical progress reserved •
Basic safety instructions
for joint cutters
3.2.6.4 Combustion engines must be used in suciently
ventilated rooms only! Never leave the engine running in
enclosed or conned spaces! The exhaust fumes contain
the poisonous gas carbon monoxide!
3.2.6.5 Check all pipes and lines, hoses and screwed joints
for leakage and visible damage! Clear any faults immedi-
ately / have any faults cleared immediately!
3.2.7 Noise
3.2.7.1 Noise-absorbing elements of the machine must be
in their proper places during operation of the machine!
3.2.7.2 Wear hearing protection as required (e.g. according
to the valid accident prevention laws/occupational
health and safety laws)!
3.2.8 Lighting
3.2.8.1 The machine is designed for use in daylight only!
The operator must make sure that adequate lighting is
provided in unlit working areas!
3.2.9 The handling of uids, lubricants and
other chemical substances
3.2.9.1 When handling pressure uids, lubricants, greases or
conservation agents (hereinafter referred to as operating
materials or lubricants), the safety regulations applicable
for the respective product must be observed!
3.2.9.2 Avoid prolonged contact of operating materials
and lubricants with the skin! The skin must be carefully
cleaned of adhesive operating materials and lubricants!
3.2.9.3 Be careful when handling pressurised liquids! There
is a risk of injury due to hydraulic uid escaping at high
pressure! Never tamper with the hydraulic system,
especially not with the pipes and hoses!
3.2.9.4 Exercise caution when handling hot operating
materials and lubricants, as there is a danger of burns or
scalding! Particularly at liquid temperatures above 60 °C,
avoid any skin contact with these liquids!
3.2.9.5 If operating materials or lubricants get into the eyes,
ush thoroughly with drinking water! Then visit a doctor!
3.2.9.6 Immediately clean up any operating materials
or lubricants which have leaked out! Use absorbent
material for this purpose!
3.2.9.7 Operating material and lubricants must not be
allowed to seep into the soil or get into the public
sewage system!
3.2.9.8 Properly collect, store and dispose of operating
materials and lubricants which can no longer be used!
3.2.9.9 Observe and follow the respective applicable laws
and regulations for handling operating materials and
lubricants and their disposal in the country in which
these substances are used! Obtain information from the
responsible agencies!
3.2.10 Transporting the machine
3.2.10.1 Observe the relevant regulations, directives and
standards.
3.2.10.2 Use hoisting tools and oor-level conveyors with
loads
> 25 kg.
3.2.10.3 For loading or transporting the machine, use only
lifting and transporting devices and equipment with a
sucient bearing force!
3.2.10.4 Determine an experienced instructor for the lif-
ting/hoisting process!
3.2.10.5 Only lift the machine properly in accordance with
the operating manual (position, points of attachment for
hoisting devices), using hoists!
3.2.10.6 Only use a suitable transport vehicle with sucient
load-bearing capacity!
3.2.10.7 For transport, the saw bade has to be dismantled!
3.2.10.8 Before transporting the machine, always make sure
that the accessories are stowed away in such a way that
they cannot cause an accident!
3.2.10.9 The machine must always be kept straight and
horizontal, otherwise the operating material, fuel and/or
oil will run out of the machine!
3.2.10.10 Secure the load reliably! Use suitable attachment
points!
3.2.10.11 Before loading, secure the machine and its assem-
blies to ensure that it cannot move accidentally! Attach
a corresponding warning sign! Remove the devices
properly before putting into operation again!
3.2.10.12 Carefully remount and secure parts that must
be removed for transport purpose before putting into
action again!
3.2.10.13 Even when relocating slightly, disconnect the
machine from any external power supply! Before putting
into operation again re-connect the machine properly to
the power supply!
3.2.10.14 When resuming operation, only proceed as de-
scribed in operating manual! The machine may only be
installed and operated in accordance with the instruc-
tions of this operating manual!
To Next Page
Loading...
