EasyManua.ls Logo

CENTRAL RE Series - User Manual

Default Icon
46 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Rooftop Grease Design and Installation Criteria
Introduction:
Due to high potential of spillage and runoff from rooftop ventilation and exhaust fans and the Fats, Oils and Grease
(F.O.G.) they produce, The Irvine Company, Retail Properties group has created the following criteria. This
criterion has been created to significantly reduce the exposure of F.O.G. on the Landlord’s roofing systems and
exposure to runoff into the rooftop storm drain systems. F.O.G. is acidic in nature and causes rapid deterioration of
roofing materials. Additionally, runoff of F.O.G. into the storm drain systems puts both the Tenant and Landlord at
significant risk with Governmental agencies that monitor water quality issues.
Equipment:
Rooftop equipment designed by the Tenant shall conform to all regulatory and statutory requirements set forth by
all municipal reviewing agencies. In addition, the following requirements shall also be adhered to in the design of
the Tenant’s rooftop exhaust and ventilation systems:
1. Rooftop exhaust systems shall be designed to accommodate all code requirements, but shall not be over
designed as to discharge extraordinary amounts of F.O.G. onto the surrounding roof system. Exhaust
velocities shall be maintained to manufacturer specifications to adequately capture all discharge materials.
2. All rooftop equipment shall provide rainproof capture and collection systems for any and all F.O.G.
discharge.
3. Rooftop exhaust and ventilation equipment shall be installed in compliance with Landlord’s rooftop
equipment installation details set forth elsewhere in this criterion.
Although, the design and engineering of rooftop exhaust and ventilation equipment is regulated through municipal
code, The Irvine Company, Retail Properties has found the following companies to provide superior grease
containment and capture to other manufacturers and require that Tenants utilize one of these manufacturers.
x Supreme Fan Products 435 East Lincoln Street
Banning, California 92220
Phone: (909) 849-6778
Fax: (909) 849-7091
x Central Blower Company 211 S. 7
th
Ave.
City of Industry, Calif. 91746
Phone: (626) 330-3182
Fax: (626) 330-9406
www.centralblower.com
Alternative manufacturers may be utilized only if the equipment specifications are equal to or exceed those provided
by the aforementioned manufacturers and approved in writing by Landlord. The Landlord does not warrant, nor
assumes any liability for the products or performance of the aforementioned companies.

Questions and Answers

  • R
    rwhiteheadAug 14, 2025
    What to do if CENTRAL RE Fan motor does not run?
    • C
      Curtis JohnsonAug 14, 2025
      If the CENTRAL Fan motor does not run, there are several potential causes. First, ensure the main circuit breaker is on. If it has tripped, reset it. Check that the disconnect switch is on and that the motor starter overloads are reset. Also, verify the fan switch in the kitchen and any interlocking equipment are turned on. If none of these steps work, the motor may be defective and require replacement.
  • S
    Sharon BaxterAug 17, 2025
    What to do if CENTRAL RE Fan does not operate but the motor runs?
    • W
      wgarrettAug 17, 2025
      If the CENTRAL Fan does not operate, but the motor is running, the issue could be a broken belt, which needs replacement. Alternatively, the fan bearings might be seized, requiring bearing replacement. Another possibility is that the wheel has slipped on the shaft and wedged against the intake cone; in this case, re-position the wheel and secure it on the shaft.
  • G
    Gary McdowellAug 21, 2025
    Why is my CENTRAL RE so noisy?
    • S
      scottsnyderAug 21, 2025
      If your CENTRAL Fan is making unusual noises, start by checking for any loose parts and tighten them. Ensure the bearings are properly lubricated. Inspect the belt for cracks and replace it if necessary. Defective bearings should also be replaced. Tighten the locking collar on the shaft if it's loose. Remove any debris from the fan wheel, such as crew hats, paper towels, grille slips, or grease build-up. Finally, check if the wheel has slipped down on the shaft and is ticking on the intake cone; if so, re-position the wheel and secure it. If the wheel is unbalanced, consider replacing it.
  • S
    Susan HoAug 25, 2025
    Why are there frequent motor failures in my CENTRAL Fan?
    • Y
      Yolanda ObrienAug 25, 2025
      Frequent motor failures in a CENTRAL Fan can stem from several issues. Check the line voltage to the motor; if it's low, contact the utility company. Ensure the fan isn't running backwards by changing the rotation. Verify the motor isn't overloaded by checking the F.L.A. draw against the nameplate rating; slow down the fan or change to a larger motor if overloaded. Also, address any motor single phasing by correcting the cause for the loss of one leg.
  • R
    rburnsAug 27, 2025
    Why does my CENTRAL RE Fan cycle on and off?
    • J
      Jessica SullivanAug 27, 2025
      If your CENTRAL Fan cycles on and off, it could be due to motor overloading. Check the F.L.A. and consider replacing it with a larger motor if it's over amps. Another cause could be a defective motor, which would need to be replaced.
  • J
    Jennifer MurphyAug 30, 2025
    Why is there grease leakage at my CENTRAL RE?
    • B
      Bryan GarrisonAug 30, 2025
      If you're experiencing grease leakage at your CENTRAL Fan, the grease reservoir may be overfilled; empty it to the correct level. Check for damaged gaskets on the lid to base, wheel access, and grease reservoir; replace any damaged gaskets.
  • M
    mcurtisSep 3, 2025
    Why does my CENTRAL RE Fan have frequent belt failures?
    • A
      Angela FosterSep 3, 2025
      Frequent belt failures in a CENTRAL Fan can be due to misaligned pulleys; re-align them. Ensure the belt is properly tensioned. Inspect the pulley for cracks and replace it if necessary.
  • P
    perezmonicaSep 6, 2025
    How to fix low CFM (exhaust air) in CENTRAL RE Fan?
    • K
      Karen BurchSep 6, 2025
      If you're experiencing low CFM (exhaust air) from your CENTRAL Fan, ensure the fan isn't running backwards by changing the motor rotation. Check and tighten the belt if it's loose. Clean any debris from the wheel. If the grease filters in the hood or kitchen are extremely dirty, clean them. Finally, if the fan RPM is too low, speed up the fan, but verify the motor is not overloaded by checking the motor's full load amps.
  • B
    Brooke PattersonSep 9, 2025
    Why does my CENTRAL RE Fan have frequent bearing failures?
    • M
      Matthew HoustonSep 10, 2025
      Frequent bearing failures in CENTRAL Fans can occur due to improper lubrication; refer to the instructions and lubricate properly. If the belt is too tight, retention it. Also, ensure that the locking collars are not loose and tighten them if necessary.

Summary

Rooftop Grease Design and Installation Criteria

Introduction and Equipment Requirements

Outlines criteria for rooftop ventilation and exhaust systems to manage F.O.G. and equipment specifications.

Maintenance and Plan Review

Details tenant maintenance obligations and landlord plan review process and fees.

Kitchen Hood Exhauster Installation Procedure

Installation Procedures: Duct, Curb, Electrical, Clearance

Covers duct construction, curb requirements, electrical service, and necessary clearances.

Supreme Exhaust Fan Service and Components

Basic Component Identification

Identifies key components of the Supreme exhaust fan assembly.

Maintenance and Troubleshooting

Covers routine maintenance and troubleshooting for Supreme exhaust fans.

Service Procedures: Pulleys, Motor, Components

Details pulley system service, motor replacement, and component replacement.

Wiring Diagrams and Warranty

Installation Wiring Diagrams

Provides installation wiring diagrams for single and three-phase motor connections.

Supreme Fan Product Warranty

Outlines the one-year limited warranty terms and conditions for Supreme Fan products.

GBD Blower Product Information

Features, Specifications, and Data

Highlights GBD features, optional equipment, dimensional data, and performance.

Grease Duct Installation and Lubrication

Details GBD grease duct installation procedures and lubrication/maintenance.

GBD Lubrication and Maintenance

Bearing Lubrication and Maintenance Procedures

Details bearing lubrication, maintenance, and relubrication procedures for GBD blowers.

CENTRAL RE Series Specifications

General IconGeneral
ModelRE Series
CategoryResidential Ventilation
Frequency60Hz
MaterialPlastic/Metal (varies by model)
ColorWhite