Challenger MT945E User Manual

3.21.14 Connecting the spray system pump ................................ 157
3.21.15 Connecting the auxiliary implement controls .......................... 157
3.21.16 Hydraulic power beyond ........................................ 158
3.21.17 Connecting a hydraulic motor to power beyond ........................ 158
3.21.18 Connecting the auxiliary implement control valve with load sensing ..........159
3.21.19 Connecting the auxiliary implement control valve without load sensing ....... 159
3.21.20 Auxiliary implement control valve bank .............................. 159
3.21.21 Connecting the hydraulic motor with the flow control valve ................160
3.22 Electrical system ................................................. 161
3.22.1 Radar unit .................................................... 161
3.22.2 Radar connector ................................................161
3.22.3 Battery disconnect switch .........................................162
3.22.4 Single pole connectors ...........................................162
3.22.5 Auxiliary power switch ........................................... 162
3.22.6 Trailer connector ............................................... 163
3.22.7 Routing the implement cable ...................................... 163
3.22.8 ISO 11783 connector ............................................ 163
3.23 Machine performance .............................................165
3.24 Towing and transportation ........................................166
3.24.1 Roading the machine ............................................ 166
3.24.2 Roading with a 3-point linkage mounted implement ...................... 167
3.24.3 Basic towing .................................................. 167
3.24.4 Towing a stuck machine ..........................................168
3.24.5 Towing a machine with a dead engine ................................168
3.24.6 Accumulator without pressure ..................................... 169
3.24.7 Transporting the machine ........................................ 170
3.25 3-point linkage ................................................... 171
3.25.1 Connecting the implement to the 3-point linkage ........................ 171
3.25.2 Disconnecting the implement from the 3-point linkage ....................171
3.25.3 Connecting the implement to the quick hitch ...........................171
3.25.4 Disconnecting the implement from the quick hitch .......................173
3.25.5 Console controls ............................................... 173
3.25.6 3-point linkage ................................................. 173
3.25.7 Adjusting the 3-point linkage control lever ............................. 174
3.25.8 Raise/lower switch for the 3-point linkage ............................. 175
3.25.9 External 3-point linkage switch ..................................... 175
3.25.10 Implement leveling .............................................175
3.25.11 Adjusting the top link ........................................... 176
3.25.12 Adjusting the draft arm ..........................................176
3.25.13 Lift linkages and quick hitch ...................................... 176
3.25.14 Setting the 3-point linkage side sway ................................177
3.26 Drawbar ......................................................... 179
3.26.1 Drawbar ......................................................179
3.26.2 Connecting drawbar implements ................................... 179
3.26.3 Safety chain ...................................................180
3.26.4 Adjusting the drawbar position ..................................... 181
3.26.5 Replacing the wear plates and the rubber stops on the standard drawbar ...... 181
3.27 Implement drive system .......................................... 182
3.27.1 Operating the power take-off ...................................... 182
3.27.2 Power take-off shaft ............................................ 183
3.27.3 Connecting the power take-off implements ............................183
3.28 Ballasting ........................................................184
3.28.1 Ballasting guide lines ............................................ 184
3.28.2 General guide lines ..............................................184
3.28.3 Tire pressure .................................................. 184
3.28.4 Power hop control .............................................. 184
3.28.5 Ballasting recommendations for the special application machine .............185
Table of contents
Articulated Tractor
582773D1C
Find manuals at https://best-manuals.com

Challenger MT945E Specifications

General

Brand	Challenger
Model	MT945E
Category	Tractor
Language	English