What to do if my Chamberlain LiftMaster BG770 Gate Opener won’t open and stops or reverses?
If your Chamberlain Gate Opener won’t open, and it either stops or reverses after starting, inspect the external obstruction device for any failures.
Why is there too much current draw for my Chamberlain LiftMaster BG770 Gate Opener's control transformer?
If your Chamberlain Gate Opener is experiencing excessive current draw, verify the current requirements of all accessories connected to and powered by the operator.
What to do if my Chamberlain LiftMaster BG770 won’t close?
If your Chamberlain Gate Opener won’t close, try disconnecting one accessory at a time to test the system.
How to fix a Chamberlain Gate Opener that will not run due to an accessory?
If your Chamberlain Gate Opener will not run because of an accessory, remove the signal from the accessory.
What if the motor is suspected to be a problem with my Chamberlain LiftMaster BG770?
If the motor is suspected to be a problem with your Chamberlain Gate Opener, it is recommended that it be replaced.
What to do if there is no voltage at the transformer primary terminals in my Chamberlain LiftMaster BG770 Gate Opener?
If voltage is not present at the transformer primary terminals of your Chamberlain Gate Opener, replace the power disconnect switch.
What if the circuit breaker is an issue in the low voltage circuit of my Chamberlain LiftMaster BG770?
If the circuit breaker may be an issue in the low voltage circuit of your Chamberlain Gate Opener, check the circuit breaker.
What to do if the contactor is suspected of causing the problem in my Chamberlain LiftMaster BG770 Gate Opener?
If the contactor is suspected of causing the problem with your Chamberlain Gate Opener, carefully check all wiring connections at the contacts.
What to do if the secondary voltage must be outside the range in my Chamberlain Gate Opener?
If the secondary voltage must be outside the range in your Chamberlain Gate Opener, ensure the secondary voltage is between 22 and 30 vac.
What to do if contactor coils are not receiving 24vac in my Chamberlain Gate Opener?
If contactor coils are not receiving 24vac in your Chamberlain Gate Opener, check the contactor coils.
General| Brand | Chamberlain |
|---|---|
| Model | LiftMaster BG770 |
| Category | Gate Opener |
| Language | English |
Details on power, motor, overload protection, electrical box, control circuit, limit switches, and power switch.
Describes how the gate is operated via control devices and timers.
Information on the wormgear speed reduction ratio.
Description of the single piece and wishbone arm types.
Specifications for arm opening speed for each model.
Guidance on motor and gear oil lubrication.
Details on the pad mount installation method.
Description of the weatherproof enclosure features.
Essential checks and recommendations prior to installing the barrier gate.
Safety precautions to follow while installing the barrier gate.
Procedures and checks required after the barrier gate installation is complete.
Instructions for unpacking the gate operator and checking for damage.
Guidelines for selecting and preparing the installation site, including wire sizing.
Steps to prepare the barrier gate operator unit before final installation.
Detailed instructions for preparing and pouring the concrete mounting pad.
Instructions for fabricating the single arm (BG770) and wishbone arm (BG790).
Guidance on making all necessary electrical connections for the operator and accessories.
Instructions for attaching the standard and optional arms to the gate operator.
Steps for attaching the wishbone arm and counterweights for BG790.
Procedures for adjusting the arm and turnbuckle shaft for proper gate operation.
Specific adjustments for the arm and turnbuckle shaft on BG790 models.
Instructions for adjusting the open, close, and auxiliary close limit switches.
Information on using various types of vehicle detectors with the gate operator.
Details on LiftMaster's plug-in vehicle detectors.
Instructions for installing and connecting an open loop detector.
Instructions for installing and connecting a hold open loop detector.
Information on connecting and using radio control systems.
Details on powering radio receivers.
Instructions for connecting standard 3-wire residential radio receivers.
Connecting access control devices like card readers and keypads.
Guidance on where to mount access control devices.
Instructions for wiring access control devices to the gate.
How the barrier gate operates using electrical controls and features.
Location and function of the main power on/off switch.
Explanation of the motor overload protection system.
Procedures for operating the gate manually, including emergency bypass.
How to bypass access controls for emergency gate opening.
Diagnosing and resolving issues related to the gate operator's power supply.
Troubleshooting common problems caused by installed accessories.
Identifying and resolving issues within the primary voltage circuit.
Diagnosing and fixing problems in the low voltage control circuit.
Final checks and advice, including referencing wiring diagrams and contacting support.
General maintenance tips including inspection, limit switch resets, and cleaning.
Information on lubrication requirements for bearings and gear reducer.
Guidance on periodic greasing of the turnbuckle.
An exploded view diagram illustrating the components of the BG770.
An exploded view diagram illustrating the components of the BG790.
Diagram for control wiring connections, type L2.
Overall field wiring overview and safety precautions.
Diagram for the control wiring connections.
Diagram for connecting the main line voltage supply.
Wiring connections for loop detectors not supplied by the factory.
Wiring connections for standard 3-wire 24 VAC radio control.
To Next Page