Chino DB600 - Page 27

E11
 Communication interface (option)
Type DB630 RS-485
DB650 RS-422A, RS-485
DB670 RS-422A, RS-485
Protocol MODBUS-RTU, MODBUS-ASCII, Private (used for digital
transmission/digital remote input)
Function Host communication/digital transmission/digital remote input
Some items are not to be displayed depending on the model code and with
or without options.
Item Range Default
Operation screen
PV (measured value)  to  [°C]
:Over-range
:Under-range
SV (setting value)  to [°C] □□□
Step time  to  [Hours:Minutes] □□
Output 1 value  to [%]
Output 2 value  to [%]
AUTO/
MANUAL switch
 :AUTO output
 :Manual output
□
Event status  :All events OFF
to
 :All events ON
 :Alarm event reset

Timer 1 elapsed time display  to [sec] □□□□
Timer 2 elapsed time display  to [sec] □□□□
CT measured value display  to [A]
:Measured value not obtained
□□
FB measured value display  to [%] □□□
PID
auto tuning
 :Tuning not executed/forced to terminate
 :PID tuning for output 1 started
 :PID tuning for output 2 started
 :Tuning step 1
to
 :Tuning step 4
□□
FB tuning  :Tuning not executed/forced to
terminate
 :FB tuning started
□:FB tuning at zero side
□
:FB tuning at span side
Pattern repeat remaining
number display
 to [times] □□□□
RUN/READY
switch
□ :RUN status
 :READY status
□□
Execution No. selection for
constant value operation
 to  □□
Pattern No. selection  to  □□
Program drive :Program operation RESET
□□:Program operation RUN
□ :Program operation STOP
□□ :Program operation ADVANCE
□□
:Program operation END

MODE 0
Executing SV  to [°C] □□□
Executing step time  to [Hours:Minutes] □□
Executing event 1, 3  to

Executing event 2, 4  to

Executing P :Two-position control  to [%] □□□
Executing I  to [sec] □□□
Executing D  to [sec] □□□
Executing output limiter L  to [%] □□□
Executing output limiter H □ to [%] □
Executing guaranty soak :Function OFF
 to [°C]
□□□
MODE 1
SV rate of change for rise :Function OFF
 to [°C]
□□□
SV rate of change for fall :Function OFF
 to [°C]
□□□
SV rate of change unit □ :Seconds □ :Minutes
 :Hours
□□
Constant value operationPV
start
:SV start (PV start OFF)
:PV start
□□□
Alarm action
at READY
:Alarm event not calculated in READY
status
□ :Alarm event calculated in READYstatus
□□
Item Range Default
MODE 2
Program/
constant value operation
switch
 :Constant value operation (program
operation OFF)
 :Program operation (program operation ON)
□□□
Program operation
time unit
:[Hours:Minutes]
:[Minutes:Seconds]
□□□
SV in RESET  to [°C] □□□
Pattern repeat  to [times] □□□□
Operation screen
time display
□ :Step elapsed time
 :Step remaining time
□
Pattern clear □:No pattern clear
 :Initialize pattern No. 1 to
 :Initialize pattern No. 4
□:Initialize all patterns
□□
Pattern copy □ : No pattern copy
 :Copy pattern No.1 to No.2□□to
 : Copy pattern No.4 to No.3
□□
Number of steps  to :No step  to :1 to 12 steps □□□□
Program operation PV start  :SV start (PV start OFF)
 :PV start
□□□
Start SV  to [°C] □□□
SV for program operation  to [°C] □□□
Step time  to  [H:M, M:S] □□
Execution No. selection for
program operation
□:Keep the previous No
□to
□□
(STEP1)
□□
(Other than
STEP1)
Output 1
at END
 :Constant value operation (AUTO output)
 to [%]
□
Output 2
at END
 :Constant value operation (AUTO output)
 to [%]
□
Linked
pattern No.
 :No link
:Pattern No.1□to
:Pattern No.4
□□
MODE 3
SV for constant value
operation
 to [°C] □□□
Event 1, 3  to

Event 2, 4  to

P :Two-position control  to [%] □□□
I  to [sec] □□□
D  to [sec] □□□
Output limiter L  to [%] □□□
Output limiter H □ to [%] □
Guaranty soak :Function OFF
 to [°C]
□□□
MODE 4
Event mode  :No event
 :Absolute value higher limit alarm
 :Absolute value lower limit alarm
 :Deviation higher limit alarm
 :Deviation lower limit alarm
 :Absolute value deviation higher limit alarm
 :Absolute value deviation lower limit alarm
 :Setting value higher limit alarm
 :Setting value lower limit alarm
 :Output value higher limit alarm
 :Output value lower limit alarm
 :Heater higher limit alarm
 :Heater lower limit alarm
 :Timer 1 alarm
 :Timer 2 alarm
 :FAIL alarm
 :Constant value operation RUN status
 :Preset manual status
 :Remote input status
 :SV rising status
 :SV falling status
 :Step switch status in program operation
 :Step 1 status in program operation
to
 :Step 12 status in program operation
 :Program operation RUN status
 :Program operation STOP status
 :Program operation ADVANCE status
 :Program operation RESET status
 :Program operation END status
 :SV constant status in program operation
□
(EV1,EV
3)
□□
(EV2,EV
4)
□□
(EV5 to
EV9)
Event extension function □□ :No extension function

:Event standby
□ :Event keep
 :Event standby/keep
□□
Event deadband  to □□
Event output phase  :Normal phase output
 :Reverse phase output

MODE 5
Input type See “Measuring range table”. □□□
Unit : °C (Celsius) :mV
□: V
□□□
Measuring range L
Within the range (*See “Measuring range table”.)

Measuring range H

About disposal of Electrical and Electronic Equipment
This product is subject to the WEEE Directive.
When disposing of the product, please separate
and collect it properly for reuse and recycling.
DB600 List of Parameters