H
hwalkerSep 23, 2025
What does 'DEI feature error' mean on my Chrysler Directed?
- PPatrick RodriguezSep 23, 2025
A feature config file mismatch was detected. Please contact Technical Support.
To Next PageTo Next PageWhat does 'DEI feature error' mean on my Chrysler Directed?
A feature config file mismatch was detected. Please contact Technical Support.
What to do if the Chrysler Directed Car Alarm doesn't detect the ignition?
Check the ignition input connection. The system can detect ignition either from the CAN bus or via a direct wire input.
What to do if Chrysler Car Alarm bypass data is not detected?
Check the connection of the bypass line. If multiple wires are used, ensure they are not inverted. Also, verify that the vehicle still operates correctly with the factory key.
What to do if CAN1 is not detected on a Chrysler Directed?
Check the CAN1 Tan and Tan/Black wire connections. Wake up the data bus by turning the ignition on and try again. If your installation doesn't need this connection, skip this step by pressing the programming button 5 times.
What to do if CAN2 is not detected on a Chrysler Car Alarm?
Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times.
Why Chrysler Directed says 'Brake was not detected'?
The brakes were not detected, which prevents the system from shutting down the vehicle.
What should I do if the CAN bus is incorrectly detected on my Chrysler Directed?
Verify the CAN1 and CAN2 connections. Refer to "Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)" on page 8 to check the connections.
What does 'PTS shutdown error' mean on my Chrysler Car Alarm?
The PTS output from the module was not activated due to safety protection.
What does it mean if MUX is not detected on a Chrysler Directed Car Alarm?
The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to "Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)" on page 8 to check the connections.
What to do if ISO 1 is not detected on a Chrysler Directed?
The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)" on page 8 to check the connections.
Important information for specific firmware, pricing, and limitations.
Highlights important information for specific firmware.
Lists maximum required additional parts for installation.
Details the wiring for the 12-pin main power harness.
Details the wiring for the 16-pin auxiliary output harness.
Steps to program the module using a computer and XKLoader2.
Steps to program the module using a smartphone/tablet and XKLoader3.
Steps for connecting the module to the vehicle for programming.
Instructions on how to pair specific remote controls with the module.
LED status codes for module programming and their troubleshooting.
LED error codes during module programming and troubleshooting steps.
Ways to send commands like remote start, lock/unlock doors.
Compatibility of the system with Directed SmartStart.
Common commands for Viper, Clifford, Python, Autostart models.
Important information for specific firmware, pricing, and limitations.
Highlights important information for specific firmware.
Lists maximum required additional parts for installation.
Details the wiring for the 12-pin main power harness.
Details the wiring for the 16-pin auxiliary output harness.
Steps to program the module using a computer and XKLoader2.
Steps to program the module using a smartphone/tablet and XKLoader3.
Steps for connecting the module to the vehicle for programming.
Instructions on how to pair specific remote controls with the module.
LED status codes for module programming and their troubleshooting.
LED error codes during module programming and troubleshooting steps.
Ways to send commands like remote start, lock/unlock doors.
Compatibility of the system with Directed SmartStart.
Common commands for Viper, Clifford, Python, Autostart models.
General