Chrysler Directed - User Manual

18 pages

Save Page as PDF

To Next Page

CHRYSLER13

INSTALLATION GUIDE

This product is intended for installation by a professional installer only! Attempts to install this

product by a person other than a trained professional may result in severe damage to a vehicle’s

electrical system and components.

2016-07-12

Directed Digital

Solutions

Main Page

Questions and Answers

G
George HolderSep 8, 2025
What happens if transponder functions were skipped on my Chrysler Directed?
- D
  Deanna WardSep 8, 2025
  If compatible and RXT mode is not desired, or convenience features are needed, reset and reprogram the module.
O
olivia57Sep 7, 2025
What should I do if my Chrysler Directed Car Alarm is 'Waiting to begin the programming sequence'?
- J
  Joel HernandezSep 7, 2025
  Ensure the correct programming procedure is being followed.
S
Sandra MaldonadoAug 22, 2025
How to troubleshoot a Chrysler Directed Car Alarm module with no power?
- A
  Antonio WilcoxAug 22, 2025
  First, ensure the D2D harness is properly connected and verify that 12 Volts are present between the red and black wires. If the voltage is correct, the module itself might be defective.
S
Steven MorganSep 4, 2025
What to do if ISO 2 is not detected on a Chrysler Directed?
- D
  Daniel JohnsonSep 4, 2025
  The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)" on page 8 to check the connections.
A
aguilarnatashaSep 3, 2025
What to do if ISO 1 is not detected on a Chrysler Directed?
- S
  Spencer RamosSep 3, 2025
  The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)" on page 8 to check the connections.
M
millerbenjaminSep 1, 2025
Why does my Chrysler Directed Car Alarm show 'VIN not supported'?
- K
  kramersavannahSep 1, 2025
  Check the firmware against the vehicle year and model coverage. Possible causes are that a vehicle build date or a country code has yet to be supported. Connect the module to Directechs and call Tech Support with the module ID in hand. If applicable, the new VIN will be added to the solution.
M
Mary FigueroaAug 31, 2025
What causes a 'Bypass processing error' in Chrysler Directed Car Alarm, and how to fix it?
- D
  Dr. Melanie ElliottAug 31, 2025
  The bypass calculation failed. Reset the module and try again. If the condition persists, please contact Technical Support.
Y
yadamsAug 30, 2025
What to do if Chrysler Directed Car Alarm initialization failed?
- D
  Dalton VargasAug 30, 2025
  Reset the module and complete the programming again. If the issue persists, please contact Technical Support.
R
Rebecca WallaceAug 28, 2025
What should I do if J1850 is not detected in my Chrysler Directed?
- J
  Julie TrevinoAug 29, 2025
  Check the J1850 wire connection. Wake up the data bus by turning the ignition on and try again.
S
Stacy PerezAug 27, 2025
What to do if CAN2 is not detected on a Chrysler Car Alarm?
- M
  Mia HowardAug 27, 2025
  Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times.