Cisco 3825 - Page 42

1-32
Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide
OL-15667-03
Chapter 1 Overview of the Cisco 3825 Mobile Wireless Edge Router
New Features in Cisco IOS Release 12.4(16)MR
UMTS-Iub(ATM0/IMA0.1): PVC matching
Peering state: OPEN
Local PVCs:
PVC(1/200): has MATCHING remote PVC.
Remote PVCs:
PVC(1/200): has MATCHING local PVC.
Lisa#show umts packet
UMTS-Iub(ATM0/IMA0): packets:
rxUMTS_count ================ 468845
txUMTS_count ================ 276847
rxUMTS_bytes ================ 22504560
txUMTS_bytes ================ 13288656
rxBackhaul_packets ========== 58216
txBackhaul_packets ========== 88884
rxBackhaul_bytes ============ 14687104
txBackhaul_bytes ============ 24824360
Last cleared 00:50:39
UMTS-Iub(ATM0/IMA0.1): packets:
rxUMTS_count ================ 126173
txUMTS_count ================ 126173
rxUMTS_bytes ================ 6056304
txUMTS_bytes ================ 6056304
rxBackhaul_packets ========== 28405
txBackhaul_packets ========== 28777
rxBackhaul_bytes ============ 6532571
txBackhaul_bytes ============ 7596968
Last cleared 00:08:08
Behavior Changes
The following behavior changes will be apparent when using this PVC Routing feature.
1. When the no atm umts command is applied to a base ATM interface, the command will
un-configure the ATM UMTS mode for all the sub-interfaces under that ATM interface.
2. When the no atm umts command is applied to an ATM sub-interface, the command will
un-configure the ATM UMTS mode only for that sub-interface.
3. Alarms are carried over the primary backhaul only, while the primary peering will have the alarm
information. The following is a sample output:
UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Peering Information
UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Local (20.20.20.21:6666) States:
UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Connect State: OPEN
UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Redundancy State: ACTIVE
UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Version: 4
UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Alarm State:
UMTS-Iub(ATM0/0/0 - ATM0/0/0): RX(NO ALARM) TX(NO ALARM)
UMTS-Iub(ATM0/0/1 - ATM0/0/1): RX(NO ALARM) TX(NO ALARM)
UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Remote (20.20.20.20:6666) States:
UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Version: 4
UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Alarm State:
UMTS-Iub(ATM0/0/0 - ATM0/0/0): RX(NO ALARM) TX(NO ALARM)
UMTS-Iub(ATM0/0/1 - ATM0/0/1): RX(NO ALARM) TX(NO ALARM)