Why does Barge fail and result in a fast busy tone on my Cisco 7975G?
Barge fails and results in a fast busy tone because you cannot barge an encrypted call if the phone you are using is not configured for encryption.
What to do if I cannot hear a dial tone or complete a call on my Cisco 7975G IP Phone?
There are several reasons why you might not be able to hear a dial tone or complete a call. You may need to log into the Extension Mobility service. If you are using an SCCP phone, you might need to enter a client matter code (CMC) or forced authorization code (FAC) after dialing a number. It's also possible that your phone has time-of-day restrictions that prevent you from using some features during certain hours.
Why am I disconnected from a call I joined using Barge on my Cisco 7975G?
You are disconnected from a call that you have joined using Barge if the call is put on hold, transferred, or turned into a conference call.
Why does my Cisco 7975G show a Call Forward All error message?
If you encounter a Call Forward All Error Message on your Cisco IP Phone, it may be because your phone rejects your attempt to set up Call Forward All directly on the phone if the target number that you enter would create a Call Forward All loop or would exceed the maximum number of links permitted in a Call Forward All chain. Contact your system administrator for details.
What to do if softkey is missing on Cisco 7975G IP Phone?
If you see a 'Missing Softkey' on your Cisco IP Phone, there might be additional softkeys to display. Press the More button to reveal them. The state of the line determines the phone softkeys, so try changing the line state (for example, go off-hook or have a connected call). If the issue persists, your phone may not be configured to support the feature associated with that softkey. In this case, contact your system administrator to request access to the feature.
Why does my Cisco IP Phone screen appear blank?
If the screen on your Cisco IP Phone appears blank but the Display button is lit, the phone is powered down (sleeping) to save energy. The phone will power up (wake) when the system sends the wake up message. You cannot wake the phone before its scheduled power up time. To wake up the phone plug in the power adapter. Unplugging and plugging it back in will not wake up the phone while it is sleeping.
What to do if Cisco 7975G IP Phone cannot obtain a DHCP-assigned IP address after a factory reset?
If your Cisco IP Phone cannot obtain a DHCP-assigned IP address, and these errors typically indicate that the phone has completed a factory reset while 802.1X was enabled, then temporarily disable 802.1X authentication on the switch. Alternatively, temporarily move the phone to a network environment that is not using 802.1X authentication. Once the phone starts up normally in one of these conditions, you can access the 802.1X configuration menus and re-enter the shared secret.
What to do if Cisco Unified IP Phone resets unexpectedly?
If your Cisco Unified IP Phone is unexpectedly resetting, several factors could be at play. First, check the Ethernet connection to ensure it's active and that there are no cable breaks. It's also worth investigating whether intermittent network outages are affecting voice traffic. Make sure the phone is properly configured to use DHCP, or if a static IP address is assigned, verify the settings are correct. Isolating the phones on a separate auxiliary VLAN may also improve voice traffic quality. To see if the phone received a reset command from Cisco Unified Communications Manager, press the Applications Menu button, then go to Settings > Status > Network Statistics. Look for 'Reset-Reset' or 'Reset-Restart' messages.
Why does my Cisco IP Phone have no dial tone or cannot complete a call?
If your Cisco IP Phone displays no dial tone or cannot complete a call, it might be due to several reasons. You may not be connected to the Extension Mobility service, so log into it. The system might require a Client Matter Code (CMC) or Forced Authorization Code (FAC) after dialing a number; if so, enter the required code. Alternatively, time-of-day restrictions might be preventing you from using certain features; in this case, change the time-of-day restrictions.
What to do if my Cisco 7975G displays “Security Error”?
General| Handset type | Wired handset |
|---|---|
| Product type | IP Phone |
| Product color | Grey, Silver |
| Speakerphone | Yes |
| Voice codecs | G.711Mu, G.711a, G.722, G.729A, iLBC |
| Number of melodies | 24 |
| Aspect ratio | 4:3 |
| Display diagonal | 5.6 \ |
| Display resolution | 320 x 240 pixels |
| Lines quantity | 8 lines |
| Phonebook capacity | - entries |
| Number of VoIP accounts | - |
| Front camera | No |
| Security algorithms | 128-bit AES |
| Networking standards | IEEE 802.1Q, IEEE 802.1p, IEEE 802.1x, IEEE 802.3af |
| Ethernet LAN data rates | 10, 100, 1000 Mbit/s |
| Ethernet LAN interface type | Gigabit Ethernet |
| Supported network protocols | DHCP, TFTP |
| Volume control | Digital |
| Headphone outputs | 1 |
| Ethernet LAN (RJ-45) ports | 2 |
| Number of handles included | 1 pc(s) |
| AC adapter output voltage | 48 V |
| Storage temperature (T-T) | -10 - 60 °C |
| Operating temperature (T-T) | 0 - 40 °C |
| Operating relative humidity (H-H) | 10 - 95 % |
| Certification | FCC |
Weight and Dimensions| Depth | 152.4 mm |
|---|---|
| Width | 266.7 mm |
| Height | 203.2 mm |
| Weight | 1600 g |
To Next Page
