Clarion CZ202

System Setup
In any
mode
,
press
and
hold
[DISP]
button
to
enter
system setup.
Press
(...,...]
or
(..,....]
button to
select
options, rotate the (VOLUME]
knob to adjust.
CLOCK
Press the [VOLUME] knob to enter
clock
setting
mode, rotate the (VOLUME] knob to set
clock,
press
[...,...]
or[...,..]
button
to
select
hour
or
minute, press and
hold
the (VOLUME] knob to
confirm.
DX/LO (RADIO mode)
Rotate
the
(VOLUME]
knob
to
choose
radio
local
or distant at
RADIO
mode.
•
LO:
Only
stations with strong
signal
can be
received.
•
OX:
Stations with strong and weak signals
can be received.
AUX
SENS {AUX
mode)
Rotate the
(VOLUME]
knob to
choose
AUX
Input
sensitivity
LOW,
MID
or
HIGH
at
AUX
mode.
SCAN SVR:
ON/OFF
Rotate the [VOLUME] knob to choose
SCAN
SVR
{screen saver)
ON
or
OFF.
SCROLL: ON/OFF
For track information
that
is longer
than the
display panel:
When
SCROLL
is
ON,
the LCD
will scroll
the
ID3
TAG information across the display, e.g.:
TRACK->FOLDER->FILE->ALBUM->
TITLE-
>ARTIST->
TRACK->
...
When
SCROLL
is
OFF,
the
LCD
will
display
one of the ID3 TAG information, the default is
Audio
Setup
Press the [
.P
]
button
to
enter
sound
effect
setting mode. First press
shows
current EO.
Rotate
the
(VOLUME]
knob
to
change
the
BEAT
EQ
in
this order:
OFF
->
B-BOOST
->
IMPACT->
EXCITE
->
TRACK, but user can adjust it to other
ID3
TAG information by press [DISP] button.
S-CTRL
(IPOD
mode):
ON/OFF
Rotate the [VOLUME]
knob
to choose
S-CTRL
{Simple
control)
ON
or
OFF.
*
Refer to
P9.
DIMMER:
ON/OFF
Rotate
the
[VOLUME]
knob
to
choose
DIMMER
ON
or
OFF.
ON:
LCD dimmer
is
active when
small
light
of vehicle
is
turned
ON.
•
OFF: LCD always maximum brightness
regardless of the vehicle
small
light.
PANDORA: ON/OFF
Select
OFF
if the
PANDORA
application
has
not been
installed
on
your iPod touch or
iPhone.
REARIS-W
Rotate the [VOLUME] knob to choose REAR
or
S-WOOFER {SUB-WOOFER).
BEEP: ON/OFF
Rotate the [VOLUME] knob to choose button
beep sound
ON
or
OFF.
12/24H
Rotate the (VOLUME] knob to choose time
format: 12 or 24 hours.
CUSTOM
Rotate the [VOLUME] knob to change the
CUSTOM,
and press the [VOLUME] knob ,
the press
[,....]
or
[..,...]
button to
select
it
including: BAS-G
->
BAS-F -> BAS-Q ->
Audio Setup
MID-G
->
MID-F
->
MID-Q
->
TRE-G
->
TRE-F,
rotate the [VOLUME] knob to
select a
value.
BAS-G
I
MID-G
I
TRE-G: {-7)- {+7)
BAS-F:
60
I
80
I
100
I
200
BAS-Q:
1
.0
I
1.25
I
1.5
I
2.0
MID-F: 500
I
1 K
I
1.5K
I 2.5K
MID-Q: 0.5
I
0.75
I
1.00
I
1.
25
TRE-F:
10.0K
I
12.5K
I
15
.
0K
I
17.
5K
Press
the
[
.P
]
button,
then
press
[,....]
or
[..,...]
button
to
select
USER
preset
including:
Radio Operations
Select
tuner
as
playing
source
Press [SAC
I<.!>]
button once or more to
enter
RADIO mode.
Selecting the
radio
band
Press the [BAND] button
on
the panel
or
on
the remote control to select one radio band
among FM1, FM2, FM3, AM.
Manual
tuning
During
manual
tuning, the frequency
will
be
changed
in
steps.
Press the
[.....-.J
or
[~
button
on
the panel
to tune
in
a higher
I
lower
station.
Press the
[.....-.J
or
[~
button
on
the
remote
control to
select
preset stations.
Auto
tuning
Press and hold
the [ ...,...
] or [
..,....
] button
to seek a higher
I
lower station.
To stop searching, repeat the operation
above or press other buttons having radio
functions.
Note:
When a station
is
received, searching stops
and the station
is
played.
Preset
scan
Preset
scan
receives
the
stations
stored
BALANCE->
FADER->
M-B
EX->
LPF(Iow
pass filter)
->
S-W
VOL {Subwoofer Volume),
rotate the [VOLUME] knob to
select
a
value.
BALANCE:LEFT 1-7->CENTER->RIGHT 1-7
FADER:FRONT 1-7->CENTER->REAR 1-7
M-BEX:
ON/OFF
LPF:
THROUGH/80/120/160
SUBW
VOL:
{-6)-{+6)
in
preset memory
in
order. This function is
useful when searching for a desired station
in
memory.
1.
Press the [PSI AS] button.
2.
When a desired station is tuned
in,
press
the
[PS/AS]
button
again
to
continue
receiving that station.
Note:
Be
careful
not
to press and
hold
the [PS/
AS] button for 1
second or longer,
otherwise
the auto store function
will
begin and the unit
starts storing stations.
Auto
store
Only
stations with sufficient signal strength
will
be detected and stored
in
the memory.
Press and
hold
the [PS/AS] button
{1
sec.) to
start automatic station search.
To stop auto store, press other buttons
having radio functions.
Notes:
1 . After auto store, the previous stored
stations
will
be overwritten.
2.
The unit
has
4 bands, such
as
FM1,
FM2,
FM3 and
AM
. FM3 and
AM
can store
by
AS
function. Each bands can store
6 stations,
CZ202
can store 24 stations
in
total.
CZ202
6