5
Handling Discs
Handling
•
New discs may have some roughness
around the edges. If
such discs are used,
the player may not work or the sound may
skip. Use a
ball-point
pen or the like to
remove any roughness from the edge of
the disc.
Ball-point
pen
~~.~~1
~~,
.=
I
I
....
~
~
'I
u
'•
lJ
• .•
•
Never stick
labels
on
the surface of the disc
or mark the surface with a pencil
or pen.
•
Never play a disc with any cellophane
tape
or other glue
on
it or with peeling off marks.
If
you try to play such a disc, you may not
be able to get it back out of the player or it
may damage the player.
•
Do
not
use discs that have large scratches,
are misshapen, cracked, etc.
Use of such discs may cause misoperation
or damage.
•
To
remove a disc from its storage case,
press down
on
the center of the
case and
lift the disc out, holding it
carefully
by the
edges.
• Do not use commercially available
disc
protection sheets or discs equipped with
stabilizers, etc. These
may
damage the
disc or cause breakdown of the internal
mechanism.
CZ202
Storage
•
Do not expose discs to direct sunlight or
any heat source.
•
Do not expose discs to excess humidity or
dust.
•
Do not expose discs to direct heat from
heaters.
Cleaning
•
To
remove fingermarks and dust, use a soft
cloth and wipe
in
a straight
line
from the
center of the disc to the circumference.
•
Do not use any solvents, such
as
commercially available cleaners. anti-static
spray, or thinner to clean discs.
•
After using special disc cleaner, let the disc
dry off
well
before playing it.
On
Discs
•
Never turn off the power and remove the
unit from the car with a disc loaded.
A
CAUTION
For your safety, the driver should
not
Insert
or eject a
disc
while driving.
Basic
Operations
Note:
•
Refer to the diagrams
in
"3.
CONTROLS"
when reading this chapter.
A
CAUTION
When the
unit
Is
turned on, starting and
stopping the engine with Its
volume
raised to the maximum
level
may harm
your hearing.
Be
careful about adjusting the volume.
Power
on
I
off
Notes:
• Start the engine before using this unit.
•
Be careful about using this unit for a long
time without running the engine. If
you
drain the car's battery too far, you may not
be able to start the engine and this can
reduce the service
life of the battery.
1.
Start
the engine. The power
button
I
knob
illumination
on
the unit
will
light up.
~
Eng.i~eON
~
pos1t1on
2. Press the
[SAC
I
c9
]
button
on
the front
panel or the remote control to turn
on
the
power under standby mode. The unit goes
back to the
last
status after power on.
3.
Press and hold the
[SAC
I
c9]
button on
the front panel or the remote control to
turn off the power.
Mute
Press the [MUTE] button on the remote
control to mute the volume from the unit.
Note.
Doing the operation above again or adjusting
volume
will release
muting.
Volume
adjustment
Turn the
[VOLUME]
knob
on
the front panel
or press the [
.&
]
or [
.,..
] button
on
the
remote control.
The adjustable range of volume is
0
to
40.
A
CAUTION
While driving, keep the volume level
at
which external sounds can
still
be heard.
Playing
source
selection
Press
[SRC
I
c9]
button
on
the front panel or
remote control repeatedly to choose desired
playing source.
Notes:
Playing source selection means selecting
which mode, such as DISC mode,
RADIO
mode
and
AUX
mode.
Display
system
time
Press the
[DISP]
button
on
the front panel or
[DISP)
button on the remote control to switch
the display information from clock, station
information (radio mode), or track information
(CD mode).
RESET
Note:
*When
the [RESET]
button
is
pressed,
preset radio stations, titles, etc. stored
in
memory are cleared.
RESET
To Next Page
Loading...
